cisco workgroup switch

Cisco 3550 switch stp learning notes STP (Spanning Tree Protocol) (IEEE 802.1D) Spanning Tree Protocol-review the working principles of SW: 1. the frame it forwards cannot be modified. create a MAC-PORT ing table based on source MAC learning. forward the frames in the target MAC ing table directly from the corresponding port. for frames without target MAC ing/Target wide (Group) broadcasting, SW learns diff

Cisco switch QoS Speed limit configuration steps:1. Enable Global QoS2. Set the ACL matching traffic3. Set a class-map to match the ACL set in the second step4, set a Policy-map match Class-map, and then define a series of policies here, limit the bandwidth bitwise (BIT) for the calculation, burst in bytes (byte) calculation5, apply the POLICY-MAP to the corresponding interfaceMLS QoSIP Access-list Extended

When we want to perform permission rating management on a Cisco router or switch, it is often necessary to assign different levels of users a command that exceeds the default settings, such as show run, which is the most basic troubleshooting command.However, the command cannot be executed when your user level is at 0-14. You can assign permissions to these users using the following command:Privilege EXEC l

message are correctIf a large number of messages are sent, the network bandwidth will be exhausted to form another Denial-of-Service attack.3. The client can specify the IP address at will.The client does not have to use the DHCP service. It can set IP addresses in a static way. If any,This will greatly increase the possibility of network IP address conflict.II. Introduction to DHCP Snooping TechnologyDHCP Snooping is a DHCP security feature. Cisco s

Cisco switch snmp setting commandCisco switch snmp setting command (from Cisco switch command list)94. set snmp Command Options: set snmp community {read-only | ready-write | read-write-all} [community_string]95. set snmp trap Command Format:Set snmp trap {enable | disable}

Cisco L3 switch Policy Routing for network access and Traffic DistributionI. Description of the solution environment 1. There are two groups of Group1 and Group2 in the environment, respectively, to access the Internet from two different network outlets. 2. The core network is a Cisco 3560G layer-3 Switch with four VLA

When I got up this morning to go to the forum, I saw a post. Ask how to solve the following problem? A Cisco three-tier switch divides 3 VLANsVLAN 2:IP 192.168.1.1 255.255.255.0 192.168.1.254 Network SegmentVLAN 3:IP 192.168.2.1 255.255.255.0 192.168.2.254VLAN 4 IP 192.168.3.1 255.255.255.0 192.168.3.254Each VLAN can communicate with each other.Now add 1 Cisco r

to say, after you set the password for level 1, you will be asked to enter the password next time you connect to the switch and enter K, this password is the password set for level 1. Level 15 is the privileged mode password that you enter after you enter the enable command. Step 2: Set the VLAN name. Because the four VLANs belong to different switches, the command for VLAN naming is VLAN 'vlan No. 'name' vlan name ', the following code configures VL

templateHOST_NAME h17_2960sw1_3.251Service_description CHECK_TRAFFICE_G1/0/28Check_command check_switch_traffic!10128!200!400!500!800}Define Service{Use GENERIC-SERVICE,SRV-PNP; Inherit values from a templateHOST_NAME h18_2960sw1_3.247Service_description CHECK_TRAFFICE_G1/0/28Check_command check_switch_traffic!10128!200!400!500!800}6. Configure permissions (pending validation)[Email protected] ~]# chmod 777/var/tmp/check_traffic_10.10.3.249_10128.hist_dat_root__647. Restart the Nagios service[E

timeoutSwitch (config) # line consoleSwitch (config-console) # Exec-timeout 60Switch (config) # line vtySwitch (config-line) # Exec-timeout 603. Installation and removal licenseswitch# Install license Bootflash:license-fileswitch# Clear License License-fileswitch# Clear License All4. Disable and enable Telnet and SSHswitch# Config TSwitch (config) # no Telnet server enableSwitch (config) # Telnet Server enableswitch# Config TSwitch (config) # SSH server enableSwitch (config) # no SSH server ena

The combination of Huawei S2000-HI switch and cisco acs for certificationCase: Huawei S2000-HI switch and cisco acs combined certification I. Networking requirements: a company's internal network adopts unified management, send the authentication tasks for accounts and passwords of all devices to the Radius server (ACS

Layer-3 Switch for Cisco switches Although single-arm routing solves the communication problem between different VLANs, it also has its fatal defects: -The single arm itself is the Backbone link of the network, which is easy to form a network bottleneck. -The sub-interface relies on physical interfaces, and the application is not flexible -You need to view the route table for each vlan forwarding, wasting

"hard" operations on network devices. The security factor is high, but the obtained information is not accurate. For example, if the IP address of a server has been changed, we can think that the server is not connected to the network because the original IP address cannot be found on the switch. The system administrator first checks the IP address information on the server, and then finds out which port of the s