clear cisco switch config

When we want to perform permission rating management on a Cisco router or switch, it is often necessary to assign different levels of users a command that exceeds the default settings, such as show run, which is the most basic troubleshooting command.However, the command cannot be executed when your user level is at 0-14. You can assign permissions to these users using the following command:Privilege EXEC l

An instance of VLAN configuration for Cisco L3 switches and L2 SwitchesCisco VLAN implementation is usually port-centric. The port connected to the node determines the VLAN in which it resides. There are two ways to allocate a port to a VLAN: Static and Dynamic. The process of creating a static VLAN is to forcibly allocate the port to a VLAN. That is, we first create a VLAN on The VTP (VLAN Trunking Protocol) server, and then assign each port to the c

EtherChannel sum view "Port aggregation/link Bundle #sh int port-channel View" Port aggregation/link Bundle #show spanning-tree view spanning tree status#show access-list View rule status#show History View Historical input commands#show errdisable Recovery see which protections can be automatically recovered after a timeout#showerrdisable Detect ? View err-disabled reason for the state6. Configure the IP of the VLANS (config) #int VLAN 6S (

Previous page Everyone talked about Cisco Basic Operation command switch, while dragon boat holiday, the Cisco simple switch configuration, and hope you share "Happy Dragon Boat Festival"! Ok, configure the switch, first, you must enter the global configuration mode

(config) #no monitor session 1Switch (config) #endSwitch#wrSwitch#show MonitorNo SPAN configuration is present in the system.3. Other(1) Port image filtering, port mirroring can do filter.Monitor session session_number Filter VLAN Vlan-id [, |-]* * Specifies which VLANs belong to the traffic that the source port is entering, and can be emitted from the destination port.(2) Delete imageNo monitor session {S

CISCO router switch SNMPv2 configuration, cisco Router Cisco router SNMP Configuration Snmp-server community CQGASPZW-R RO // ro read-only Snmp-server trap-source Loopback0 // use the loopbackaddress as the source address of the message sent by the trap. Snmp-server host 50.1.50.3 version 2c CQGASPZW-R udp-port 9006 /

(global configuration mode)S1 (config) #interface vlan 1 --Enter VLAN 1 PortS1 (config-if) #ip address 192.168.1.1 255.255.255.0 --Configure the vlan1 with an IP address so PC1 and S1 can ping interoperabilityS1 (config-if) #no shutdown --activating VLAN 1 PortS1 (config-if) #end --Return to privileged modes1#copy ru

, one per line. End with cntl/z.Switch (config) #vlan 2Switch (Config-vlan) #exitSwitch (config) #vlan 3Switch (Config-vlan) #exitSwitch (config) #Switch (config) #int FA0/1Switch (

I. host MAC and switch port binding: Switch # config terminal Switch (config) # int f0/1 Switch (config-if) # switchport mode access Switch

timeoutSwitch (config) # line consoleSwitch (config-console) # Exec-timeout 60Switch (config) # line vtySwitch (config-line) # Exec-timeout 603. Installation and removal licenseswitch# Install license Bootflash:license-fileswitch# Clear License License-fileswitch#

current configuration information (Information in RAM) 51cto # show startup-config \ view the information of the saved disk (Information in NVRAM) 51cto # show ip route \ view route table information 51cto # show cdp neighbors \ check which cisco devices are connected to this vro 51cto # erase startup-config \ recover the vro to the factory configure 51cto # rel

cisco)SW1912 # show running-config... (Same as the configuration list in section 2nd, Which is omitted here)(1) Section 1st is the display content after 1912 switch power-on, listing the copyright information, software version information (Enterprise Edition), ethernet address (00.04, DD-4E-9C.80) and a variety of serial numbers.After the preceding information,

interface. What can I do? Because a Cisco TFTP Server upgrade requires that the Cisco switch fail to be connected to a PC with a TFTP Server installed on the network. After some look, finally found that the super engine 720 above a RJ-45 look like the interface, next to the words Link, play! The result is a try with the network cable, and the indicator light is

: On the emulator, you cannot use the show port-security command on a layer 3 switchPC Settings 192.168.1.2//pc0192.168.1.3//pc1192.168.1.4//pc2192.168.1.5//pc3//Subnet mask and gateway 255.255.255.0 192.168.1.1PC (Command prompt cmd) ipconfig//view MAC address of 4 PCs separatelySwitch0 configuration switch>enswitch#conf tswitch (config) #inter rang f0/1-22switch (conf