config router

Lab environment: DynamipsGUI 2.8 Tutorial topology: 650) this. width = 650; "style =" width: 587px; height: 275px "height =" 221 "alt =" "width =" 721 "border =" 0 "src =" http://www.bkjia.com/uploads/allimg/131227/0305341015-0.jpg

An OSPF comprehensive experiment includes nine routers (one of which is a simulated frame relay switch ), it involves multiple OSPF regions, OSPF Virtual links, Stub areas, NSSA areas, OSPF manual summary, OSPF interface authentication, OSPF region

Lab TOP:Lab requirements: You can ping the Lo0 of R7 from the Lo0 of R1 to the Lo0 of R7. On R4, 7.7.0.0 and 7.7.2.0 are displayed as OE1 7.7.1.0 and 7.7.3.0 are displayed as OE2.Tutorial configuration: www.2cto.comR1=================================

OSPF applications-single-region and multi-region (CISCO) Single-region: 1. job Requirements! Three methods for injecting default Routes 2. Topology1. the device configuration is as follows: R1 (config) # int s1/0R1 (config-if) # ip add 192.168.1.1 25

Tutorial topology: 650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M01/48/D2/wKioL1QLrYjSWubjAAFR1F2EAJA800.jpg "Title =" 1.png" alt = "wkiol1qlryjswubjaafr1f2eaja800.jpg"/> , Which belongs to the dual-point bidirectional redistribution

Introduction: like the standard OSPF protocol, the is-is protocol is a link-state dynamic routing protocol, but it is much optimized than OSPF, reducing the routing type and LSA flooding, it is also widely used in the current network. Tutorial

OSPF comprehensive experiment (1) This experiment mainly describes multiple methods of working on OSPF interfaces. Lab: The topology used is the ccnp Standard Edition ,: Certificate ------------------------------------------------------------------

Concept preview: What is multi-point bidirectional routing re-release?Different routing protocols send route information to each other through re-publishing. The number of ASBR routers for re-publishing is more than one. in each routing protocol,

Configure several experiments in a single OSPF area. 1. Configure the routing interface to start the OSPF process on R1, and configure the Router ID and the interface R1 (config) that runs OSPF) # router ospf 1R1 (config-router) # router-id 192.168.2

There may be many routing protocols in a large network, so it is related to the problem of routing redistribution. The network architecture looks like this:650) this.width=650; "Src=" https://s5.51cto.com/wyfs02/M01/97/28/wKiom1kpjcaiKoebAADEN44abCc4

Tool used in the experiment: Xiao fan Simulator 1. On router R1, configure the interface, start the ospf routing process and rip, advertise the network segment, and configure route redistribution.★☆R1 ☆★☆→Router>Router> enableRouter # config

Tool used in the experiment: Xiao fan Simulator ★☆1. Configure the interfaces of each vro and use the view command to analyze the changes in the route table and link status database. ☆★① Set interfaces f0/0 of R1 to RIP Protocol, f1/0 to OSPF

In-depth resolution of OSPF Forwarding addresses FA is short for Forwarding Address. FA is the field in the TYPE 5 LSA advertised by ASBR. Its role is to tell the router in the OSPF domain how to quickly reach the next hop address of the route

1: NBMA mode on Hub-and-spoke (also the default mode)Summary: Features of The NBMA mode on HUB-AND-SPOKE:(1) the IP addresses of the frame relay interface are all on the same subnet;(2) manually configure OSPF neighbors;(3) DR needs to be elected,

Cisco Route Protocol RIP v2 (1)This is not repeated. The one I made is RIP Version1. This is RIP Version2. If it is written into an article that is too long, it will be written separately. * Note: This article is intended for the majority of users

Rip (CISCO) Case 2 of OSPF advanced applicationsCase 2:1. Job Requirements:& Lt; 1 implement communication between networks running ospf and ripMethod: Route redistribution and injection default route& Lt; 2 configure the peripheral area& Lt; 3

I. Common technology of Campus networkUnderstand the relevant network component terminology before you begin the following operations.Two. Investigate the school situation and divide the VLAN and IP address segments VLAN number

  Experiment topology: Lab environment: GNS3 and C3640   Purpose: To verify whether the auto-load balancing function is implemented by the kernel.   Next we will start the experiment 1. Configure an IP address for R1   R1> en R1 # conf Starting ing

  Router> en Router # conf Starting ing from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. Router (config) # host R4 R4 (config) # int lo4 % LINK-5-CHANGED: Interface Loopback4, changed state

5. Configure the interface ip address and Loopback interface ip address of each router in the ospf single-domain dynamic routing protocol, steps ======================================================== ================================================