configure dhcp on cisco router

CISCO PT Simulation Experiment (18) router DHCP server and relay configurationExperimental Purpose :Master the configuration method of router DHCP serverMaster the configuration method of DHCP relay AgentMastering the

A Cisco router uses Cisco 3620 as the ios dhcp Server. the IP address of the fastethernet0 port connected to the Intranet is 192.168.1.4, And the L2 Switch uses two Cisco 2950, A layer-3 Switch uses a Cisco 3550. There are two VLA

Some time ago, my colleague asked me a question about the DHCP configuration of the Cisco router. At that time, I did not give a positive answer, because this was my first time. In the following days, I have consulted relevant materials and are satisfied with the following answers. Share it with you now! In addition, most people do not know about the computer and

In network management, we usually handle the problem about Cisco router DHCP. Our netizens also participated in some of the discussions. Here we will summarize them for your reference. There may be no specific mode to describe Cisco router

Some of the comrades may not be very clear about the DHCP configuration of Cisco routers, and most people do not know about the computer, so, the customer asked us to allow any computer to access the LAN to access the Internet, so we had to configure DHCP 2600. 2600 router we identify as:

Dhcp configuration commands for Cisco router R1 (server) -------------------- R2 (client) www.2cto.com dhcp configuration of Cisco router and their explanations are as follows: r1dhcp service configuration

Assume that two Cisco routers and R1 (server) connect to R2 (client) to form a simple chained lan. DHCP is implemented below. The configuration commands and explanations are as follows: 1. Configure the R1 dhcp Service Dhcp # configure terminal // Enter global Mode Dhcp

First, the experimental topologySecond, the specific configurationRouter (config) #do sh runbuilding configuration ... Current configuration:604 bytes!version 12.4no service Timestamps log datetime MSECNO service timestamps debug datetime MSECNO Service Password-encryption!hostname router!ip dhcp excluded-address 192.168.1.1!IP DHCP Pool ABCNetwork 192.168.1.0 25

Cisco Terminal configuration: (DHCP only)Service DHCPIP DHCP relay information trust-allInterface Vlan4IP address 192.168.4.254 255.255.255.0IP helper-address 10.0.0.11!Interface Vlan6IP address 192.168.6.254 255.255.255.0IP helper-address 10.0.0.11!650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M00/59/7E/wKioL1TUvvqTNu5WAASFSbihEBY376.jpg "title=" 2015-0

router) Ghqconfig-if #interface vlan2 (configuration VLAN2) Ghqconfig-if #ip helper-address 192.168.1.4 Turn on the Portfast feature on all two-tier access ports that are directly connected to the client For the client to obtain an IP address correctly, the Portfast function of the switch port connected to the client needs to be turned on (Cisco 2950). It is important to note that this feature can only b

255.255.255.0 VLAN1 dynamically allocates IP addresses that can be allocated within the network segment 192.168.1, but no excluded addresses) Ghqdhcp-config # default-router 192.168.1.254: configure the default gateway for the client, that is, the IP address of VLAN1) Ghqdhcp-config # ip dhcp pool vlan2 configures the address pool for VLAN2, which is a sub-pool of the global pool, the domain suffix, DN

There are many things worth learning about in the configuration of a Cisco Wireless Router. Here we mainly introduce how to use a vro to set up a PC to share the Internet, including knowledge about DHCP, security, TCP/IP network protocols, and so on. As a product designed specifically for broadband Internet sharing, a Broadband

In some vro configurations, DHCP is usually used. So today we will explain some settings in this regard. Let's take a look at the settings of cisco dhcp client and Service. DHCP defines in rf12001 that UDP is used for datagram transmission and port 67,68 is used. After Cisco

higher-level device, which is generally not selected. static IP addresses are suitable for users who provide static IP addresses for residential broadband and other ISPs, while PPPOE is used for ADSL users. Static IP settings are relatively simple, but DHCP is usually not used. Therefore, we will focus on setting PPPOE. After we select PPPOE, we will enter the ADSL user name and password, after which the router