connect sata hard drive to sas controller

SAS hard Drive, is a serial connection to the next generation of SCSI technology, the use of serial technology to achieve higher transmission speed, and by shortening the connection line to improve the internal space. SAS is a parallel SCSI interface that develops a new interface. Improves storage system performance, a

Like old SCSI and SATA technologies, SAS supports hot-swappable disks, which is important for environments that maintain high availability requirements. And SAS is a complete two-way system, while SATA inherits the IDE's characteristics and is a system of half-two-way communication. Therefore, the

compatible with the PATA device by using a multi-purpose chipset or serial-parallel converter. Because SATA and PATA can use the same drive, you do not need to upgrade the operating system or perform other changes. 5. You do not need to set the jumper of the Master/Slave disk for Sata. The BIOS will number it in the order of 1, 2, and 3. This depends on the

mode at a low cost.Nv raid:Nv raid is a raid technology developed by nvidia.Q: What is the raid level? What does raid grade mean?The development of orce series chipset is also constantly updated. Compared with other raid technologies, the nv raid of the latest nforce4 series chipset has its own distinctive features, mainly including the following:(1) cross-controller raid: A Hybrid raid, commonly known as raid, that is, combine the

makes it difficult to use as IDE hard disk, so the SCSI hard disk is mainly used in medium and high-end servers and high-end workstations.Five. SASSAS (Serial attached SCSI) is a serial-attached SCSI and is a new generation of SCSI technology. The same as today's popular serial ATA (SATA) drives, serial technology is used to achieve higher transmission speeds an

SASAndSATAHard Disk differences As you know, like ata, SCSI is a parallel technology that can connect multiple devices through their respective data channels. Like ata, SCSI is also evolving towards Serial technology, which is SAS (Serial Attached SCSI ).In short, SAS is a new generation of SCSI, which includes some improvements, such as higher transmission speed

disk. When raid is enabled, You need to load the driver. The SATA controller using a third-party chip must load the driver.For detailed steps to load the SATA driver, see the article "when the Serial ATA Hard Disk encounters WindowsXP", as follows: With the narrowing of the price gap between Serial ATA

The server configuration is as follows:XEON5506 (2. 13)Memory: KST 4GB DDR3 ECCHard drive: st300g SAS-15000 to *1+1t Western Data enterprise-class hard driveMotherboard: Asus Z8ANA-D6+6480*1Chassis: 1U rack TypePower supply: 1U 400WAfter the assembly is ready, installation of the system found in the Win2003 installation interface

hard Disk Interface The current hard disk interface type is not much, mainly IDE, SCSI, SATA three kinds. Many times the IDE replaces the Ultra ATA, many people are accustomed to the Ultra ATA hard disk is called IDE hard disk, but need to explain that the concept of the

backward-compatible with SATA. The back panel (backplane) of the SAS system can connect both a dual-port, high-performance SAS Drive and a high-capacity, Low-cost SATA Drive. Because t

SAS and SATA Hard Drive guidelines When you add a hard disk drive to the server, follow these general rules: The system will automatically set all drive numbers If you are using only

Hard Disks include SSD, HDD, and HHD. SSD uses flash memory particles for storage, HDD uses magnetic discs for storage, and hybrid hard disks (HHD: hybrid hard disk) is a hard disk that integrates the magnetic hard disk and flash memory. HDD:

Reference: http://blog.csdn.net/tianlesoftware/article/details/6009110The main types of hard disk interfaces currently available are IDE, SATA, SCSI, SAS, FC, and so on.The IDE is commonly known as the port, SATA is commonly known as the serial port, both of the hard disk is

2. In this case, you can use an XP disk to install the system. The hard disk can be recognized and XP can be installed. (This is not detailed here ). 3. go to the installed XP system, place the extracted sata965 (see the attachment) in any accessible path, and double-click "Run automatically. CMD file, you will be prompted to restart the system later.[965SATA (sats965)Driver] note that 945sata does not support 965sata drivers Http://www.325999.com

installing XP, if the board contains a third-party sata/raid chip, install the driver at the beginning of the installation, or reboot will not find the hard drive. Second, the SATA interface of the hard drive led to the blue scr

motherboard. Enabled: Parallel IDE port function (preset) is allowed. Onboard IDES operate mode (motherboard built in IDE priority setting) The device priority (default) on the PATA is Pri ide:pata port. The device on the SATA is Pri ide:sata port is preferred. Onboard sata-ide (motherboard built-in SATA port function set) Disabled: Turn off the

. Raid: A disk array (default value) can be created for the hard disk on the SATA port of the motherboard ). You only need to adjust the priority of the serial and parallel ports according to the actual situation to use the SATA hard disk normally. (From the options above we can see that here the S-ATA

What is SAS? SAS is a new generation of SCSI technology, and the popular Serial ATA (SATA)Hard DiskSimilarly, serial technology is used to achieve higher transmission speeds and improve internal space by shortening the connection lines. SAS is a new interface developed afte

stage, select drivers and bootable ISO images (Figure 2), and then click forward to go to the next step. Figure 2 5. on the "integrate drivers to installation files" page, click "insert", select "single driver" in the pop-up list, and select "D: the file "iaahci. INF "to open the file. In this case, the driver integration options interface appears. Select "text mode driver" and select "Intel (r)" in the list) 82801hem/hbm sata ahci

Sata's full name is serial Advanced Technology attachment (Serial Advanced technology Attachment, an industry-standard serial Hardware driver interface), which is made up of Intel, IBM, Dell, APT, The hard disk interface specification proposed by Maxtor and Seagate Corporation. The Serial ATA 1.0 specification was formally established in 2001 by the Serial ATA Board of Intel, APT, Dell, IBM, Seagate, and the major vendors.