connecting sata hard drive to power supply

. Currently, there are only Huayuan. For details about the models that support this function, refer: Http://www.asrock.com/product/index_china.htmIn addition, although the hard drive of the motherboard supports hot swapping, only the SATA data cable is hot-swappable without interrupting the power

the use of lines to interfere with the smaller serial lines between the signal transmission, so compared to the original parallel bus, Sata's working frequency greatly improved. Although the bus bit width is small, the SATA 1.0 standard can still reach 150mb/s, the future SATA 2.0/3.0 can be increased to 300 to 600mb/s. And S-ata has a more concise and convenient layout wiring, in the limited chassis, more

prices are too expensive. The actual transmission speed changes little. Users to pursue mature, stable products. This column more highlights: http://www.bianceng.cnhttp://www.bianceng.cn/Servers/zs/ SATA hard disk, serial connection, Serial ATA bus using embedded always signal, with stronger error correction capability, improve the reliability of data transmission. It also has the advantages of simple

motherboard. Enabled: Parallel IDE port function (preset) is allowed. Onboard IDES operate mode (motherboard built in IDE priority setting) The device priority (default) on the PATA is Pri ide:pata port. The device on the SATA is Pri ide:sata port is preferred. Onboard sata-ide (motherboard built-in SATA port function set) Disabled: Turn off the

SATA The full name of Sata is serial Advanced Technology Attachment,Proposed by Intel, IBM, Dell, APT, maxtor, and SeagateHard Disk InterfaceSpecification. The SATA hard drive adopts a new design structure, which features fast data transmission and space saving. It has m

menu under main. Under the onboard ide operate mode, you can select two ide operation modes: compatible mode and enhanced mode (compatible mode and enhanced mode ). The compatibility mode is compatible mode, which can be understood as ing the SATA hard disk port to the corresponding port of the parallel port ide channel. When you select this mode, there are three options in the following ide port settings:

Motherboard SATA connector does not recognize the hard drive reasons and solutions: One, the hard disk can not use the fault 1, BIOS setup Error Mainly in the BIOS on the SATA Setup error, especially some early motherboards using a Third-party

Article Title: perfect solution for UbuntuLinux shutdown abnormal [SATA hard drive]. Linux is a technology channel of the IT lab in China. Includes basic categories such as desktop applications, Linux system management, kernel research, embedded systems, and open source. Shut down or sleep in Linux. When the power

Embed the SATA hard drive into the Windows XP Server guard Disk Many Computers are now equipped with Sata hard disks, but the operating system Windows XP (hereinafter referred to as XP) SP2 is not integrated with a drive that

Many friends have previously asked if the SATA hard drive can use ghost. When using ghost to back up the system, they may have encountered this situation, After the system is started with a floppy disk or a CD, the system is black after the ghost. EXE command is used. Does ghost not support SATA devices? Can't we back

Many catchers have asked if they can use ghost for SATA hard disks. When using ghost to back up the system, they may have encountered such a situation. After starting the system with a floppy disk or a CD, when using ghost. after the EXE command, the system is black and crashes. Does ghost not support SATA devices? Can't we back up the system after using a

with a local SATA driver Steps: 1. Boot (remember to select the preferred Boot Mode for the optical drive in BIOS) 2. Store the Windows XP installation disk 3. Press F6 on the Start Screen. 4. Press the s key to select the device to attach 5. Put the previous floppy disk or CD in 6. Follow the prompts to continue the installation. 7. After the installation is restarted, go to the BIOS to enable the

Sata's full name is serial Advanced Technology attachment (Serial Advanced technology Attachment, an industry-standard serial Hardware driver interface), which is made up of Intel, IBM, Dell, APT, The hard disk interface specification proposed by Maxtor and Seagate Corporation. The Serial ATA 1.0 specification was formally established in 2001 by the Serial ATA Board of Intel, APT, Dell, IBM, Seagate, and the major vendors.

Many friends have acquired a notebook and encountered some difficult problems. Usually install XP when the blue screen or install half of the time the copy file failed! This is generally the problem of hard disk, here is not to say hard disk physics problems, software problems. Serial ATA hard disk, Serial ATA bus with embedded clock signal, with a stronger abil

When using the SATA interface hard disk to install XP system, there is a panic, blue screen situation, show "Unknown Hard errorsystemrootsystem32ntdll.ll" error. Since the SATA interface appears later than the XP system, the SATA driver needs to be invoked when the s

After entering the DOS, the operation of the Ghost machine will stop not moving, into a false panic phenomenon. If you enter the PE run ghost will be blue screen. The main reason for this is that the ghost version is too low (version less than 11) and does not recognize Sata's optical drives and hard drives. When the ghost starts, it detects whether the IDE hard disk exists, if there is no IDE device, it w

multi-language support package, with a total of 3 CDs. The simplified Chinese, traditional Chinese, and Korean language packs are in 3rd CDs, which can also beHttp://download.microsoft.com/download/fdafdac56ee-928a-Download 4d51-9d6d-c7c64e9f5baARMMUIx3.iso.　　Install 64-bit XP on SATA hard drive1. You must use a CD-ROM for boot installation.First, the Tester Used winrarto release ws03sp1_rtm_1830_px6_en.is

Q: SATA and SATA 2.5, the two specifications of the hard disk performance gap is large? Is it necessary to upgrade the existing SATA hard drive to SATA 2.5? A: The interface is not a p

window and restart your computer. 4. when the system starts, press "F2" (depending on the computer's key) to go To the BIOS settings page and change the hard disk to "AHCI" mode. The general position is: "Devices" → "ATA Drives Setup" → "Configure SATA as" → "AHCI", save and exit BIOS. 5. After the system is restarted, it is successfully modified to the AHCI interface standard. After the above introduction

Install Linux on SATA hard disk (earlier versions)-General Linux technology-Linux technology and application information. For details, refer to the following section. You do not need to read the latest version. Sata hard drive In the BIOS of the motherboard, you must set