The basic description of the DLT algorithm is as follows:
dlt+ Newton method
Basic ideas:
The initial value is obtained by the DLT method, and then the iterative solution is solved by Newton method.
The thinking of the DLT method:
The camera matrix p is a matrix of 3*4, a total of 12 parameters. If you do not conside
, then the situation is much more complicated. Ii. Introduction to Storage Tapes Tape storage is a fairly broad category, including DDS, LTO, DAT, DLT, SDLT, and more. For decades, various tapes have become traditional backup media. Table 1 is a list of tape technologies:
Tape type
Tape Storage works
Tape is a tape storage system is one of the most common storage media with the lowest cost, capacity, and Standardization of unit storage information in all storage media. Its interchangeability is good, easy to save, in recent years, because of the use of high error-correcting ability of the coding technology and write-read channel technolog
Back up all data on the local disk to tapeBy default, you do not need to specify the file system device number. The value is "/dev/RMT/0 m ". However, if this device does not contain tape media or you need to apply other devices, you must add the parameter "-d" and specify the device number.
# Make_tape_recovery-AVOutput result:* Creating local directories for configuration files and archive.
======= 11/28/06 14:40:15 eat started make_tape_recovery. (
average of 200,000 hours of downtime for the tape drive (the new product has reached 300,000 hours); In terms of reliability, the write-and-read function is detected immediately after the data is written, This not only ensures the reliability of the data, but also saves a lot of time. Second, this technology has a wide range of tape drives to meet the majority of network system backup needs. Third, this te
1. Definition of DLT DLT is an algorithm for solving the least squares problem with scale problems. The standard form of DLT problem solving is: Another form of expression is: Or This model is often encountered in projection geometry. For example, the pinhole camera projection model, 3D point to the image plane projection relationship; The single-response matri
, indicating that the tape is at the beginning
EOF (END Of file)
LPull another tape
If an error occurs while reading the tape, you can re-tension the tape, clean the tape drive, and then try again. Do not re-take the non-QIC tape
Continuous update ...The DLT is presented by Naiyan Wang and Dit-yan yeung of Hkust, and the articles and codes are shown in http://winsty.net/dlt.htmlRelated papers are learning a deep Compact Image representation for Visual Tracking (NIPS2013 ')The paper itself does not have too many bright spots, can say basically did not speak what.The general idea is to use Sdae (stacked denoising Autoencoder) to train a lot of data offline, the purpose of off-li
Visual Tracking Method: The DLT (deep learning tracker) is really a fire, it should be able to represent the 2013 tracking field of State-of-art. Recently, it has been carefully studied, in accordance with the framework, core ideas, the prospect of "deep analysis."
Frame
The entire algorithm is still in the mainstream pf (particle filter) probabilistic framework. PF to do is to select multiple candidate areas in one frame of image and then confirm th
Work needs to calculate the camera and the position of the object relationship, by colleagues introduced DLT, feel good on the study.
DLT Full name Direct Linear transformation
Specific algorithm description (English) in: http://www.kwon3d.com/theory/dlt/dlt.html
See the above DLT algorithm introduced, is very
Tape devices should be used only for timed file archives or for transferring data from one server to another. The general tape device is connected to a Unix machine and manipulated with Mt or MTX. It is strongly recommended that you back up all of your data to disk (perhaps in the cloud) and tape devices.In this tutorial you will learn:
Steps for adding a tape drive
1System power-off
2Check whether the SCSI address of the tape is set correctly.
The default target ID of the tape drive is 4 (the SCSI optical drive is 6)If you have multiple tapes, set the second tape drive correctly so that its SCSI address does not conflict with the current addres
15 practical Linux/Unix tape management commands for the system administrator
Tape equipment should only be used for regular file archiving or data is transferred from one server to another. Generally, tape devices are connected to Unix machines and controlled by mt or MTCs. We strongly recommend that you back up all data to disks (maybe in the cloud) and
In Linux, there are multiple ways to use the tape drive. The tar command is the most frequently used method. tar is mainly used to directly write data to the tape drive in a single-host environment. The device name of the tape drive in Linux is/dev/stX. If it is the first tape drive, that is,/dev/st0, the basic operati
Tape Drive Operation Command:
Tar command:
Use the tar command to copy a file or directory tree to a single tape.
Note: Special files such as empty directories or device files cannot be copied and cannot be used to create multiple tape volumes.
1. copy Files to tape
(1) switch to a directory that contains files th
Guide
Tape devices should be used only for periodic file archives or to transfer data from one server to another. Typically a tape device is connected to a Unix machine and controlled with MT or MTX. It is strongly recommended that you back up all your data to disk (perhaps in the cloud) and tape devices at the same time.
In this tutorial you will
AIX for system backup and recovery
Backup and recovery is what system administrators often do, including ROOTVG backups and user data backups.
Backup of operating system and System programs:
Insert a new tape or unwanted tape into the tape drive
#tctl-F (Designated tape device)/dev/rmt0 rewind (Rewind
In this tutorial you will learn:· Tape Device Name· Basic commands for managing tape drives· Basic Backup and Restore commandsWhy backup?A backup plan is necessary for regular backup files, and if you prefer not to back up, the risk of losing important data increases significantly. With backup, you have the ability to recover from a disk failure. Backups can also help you protect against:· Accidental file d
server|web| Backup | recovery | data
Absrtact: This paper introduces the working process of tape data backup and recovery, including a database with a capacity equivalent to tape on the hard disk, that is, bridge databaseAnd in the Web Information system to achieve a full backup of tape data and restore functions. This paper expounds how to use the existing datab
The usage of the tape drive-Linux Enterprise Application-Linux server application information. The following is a detailed description. In Linux, the device name of the SCSI tape drive is/dev/nst0 or/dev/st0. n indicates that the tape is not rolled back after it is backed up, so that it can be backed up on one tape mul
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.