Why useDMZHost?To open an intranet server, use the DMZ host. For example, there is a server that shares resources in the intranet to provide resources for Internet users. You can set the DMZ host to open the server to the Internet.Of course, if the server's service port is fixed and easy to set, we recommend that you use a virtual server.The DMZ host is as fo
fills in 3 of the [subnet]Mask], the default gateway fills in the [gateway address] obtained in 3, and the others are filled in as shown.5, as for [bedroom IP address], you can send a post on the BBS, and then look at the post at the bottom of the IP address displayedIs your bedroom's [bedroom IP address] ^_^Second, set up the DMZ hostThe following settings take the Tp-link R402
DMZ host (router) Introduction DMZ host provides different security levels for different resources, you can consider building a region called "Demilitarized Zone" (DMZ. DMZ can be understood as a special network area different from the Internet or intranet.
Advanced Settings of wireless routing-virtual servers and DMZ hosts this article mainly introduces the virtual servers and DMZ host functions of wireless routers, that is, allow Internet users to access the servers in the home. Therefore, if you do not have this requirement, you can skip this section. To ensure LAN security, the vro hides the IP address of the LA
Tplink Router's DMZ host setting method
First press the Windows key (that is, the window key, the CTRL right) +r, exhale the run bar, enter "cmd" (console) and then enter the console input "ipconfig" again return (used to view their address), IPV4 address this is your computer IP address.
Open the browser, enter your router address, small weave here is Tp-link
I. vro settings and computer settings
1) vro settings I, see.
2) vro settings II, see:
Change the WAN port address, LAN port address, and DHCP address range.
Key points:The WAN port set by the router is a dynamic IP AddressVroObtain the IP address, change its own IP addre
Home Wireless Router Security Settings tutorial, Wireless Router Security Settings
Nowadays, many families are secure from the home wireless wi-fi system, but many users do not know how to set up the home wireless network safely during installation. Many users feel very difficult, I think security protection operation
computer, is 192.168.0.10, if you want your friends to access this server through the default port 21 and use the TCP protocol, follow these steps:
1 .. on the port field ing page, Enter ID Start port and ID end port 21. You can also select "FTP" in "common service port number ", enter port 21 in the corresponding setting box.
2. Enter 192.168.0.10 in the Intranet IP field, select TCP protocol, and select enable.
3. Illustration:
4. Click OK.
When your friends access this FTP server, simply en
In the previous article, we introduced the basic vro settings and achieved the goal of surfing the Internet through the Basic settings. However, we cannot ignore the wireless router security settings. With security, you can enjoy the fun of wireless networks with peace of mind. So how should we perform the specific sec
TP-Link wireless router settings graphic tutorial how to set a TP-Link Wireless Router DiagramThe following describes the settings of the tp link wireless router. In this example, we use a new vro. If you are not sure whether the vro has been set before, we recommend that yo
addresses, subnet masks, gateways, and DNS servers on each computer. In addition, in the address pool start address and address pool end address, you can flexibly control the start address and end address when the DHCP server automatically assigns an IP address, let the Intranet host get the IP address between the two addresses.In addition, the built-in DHCP servers of the Broadband Router also have the static address allocation function. You can res
There are still many things worth learning about home broadband router settings. Here we will give an in-depth explanation of home broadband router settings. As the network develops faster, home network devices are gradually being recognized and accepted by everyone.
Network technologies are constantly being updated, a
the PC sends a ping, the response Reply packet's destination address is 218.59.245.195. When a router R1 a ping, the target address of the response reply packet is 218.59.0.146. The routing table entries that match 218.59.245.195 are found against the R4 routing table, and no routing table entries that match the destination address 218.59.0.146 are found. It appears that the ICMP response reply packet was discarded at R4 processing, so a PMG failure
I 'd like to introduce you to D-Link wireless router settings. Many people may not know about D-Link wireless router settings. It doesn't matter. After reading this article, you will certainly have a lot of GAINS, I hope this article will teach you more things.
Connect to a wireless
I would like to introduce you to the Cisco Wireless Router setting method. Many people may not know how to optimize the Cisco wireless router settings. It does not matter. After reading this article, you will certainly have a lot of GAINS, I hope this article will teach you more things.
I. Basic Cisco wireless router
settings. now to the System Status tab in the "System Information" to see the status of the network, at the WAN end can be clearly seen ADSL dial-up access to information. After setting up the ADSL account, we can access the Internet through the broadband router, but in order to better manage and improve security, we need to do the following: Click "Home" tab, then select "DHCP" on the left, and set the
How to restore factory settings TP-WR740N wireless router, tp-wr740n Wireless Router
Generally, there are two ways to restore the factory settings of a vro. One is to directly press the reset button on the vro; the other is 2; is in the router management interface to restor
can clearly see the network information obtained by ADSL dialing.
After configuring the ADSL account, we can set up Internet access through the Broadband Router. However, to better manage and improve security, you need to perform the following operations: click the "Homepage" tab, select "DHCP" on the left and set the ip address range in the ip address range that the DHCP server can enter. After saving the settin
the Broadband Router. However, to better manage and improve security, you need to perform the following operations: click the "Homepage" tab, select "DHCP" on the left and set the ip address range in the ip address range that the DHCP server can enter. After saving the settings, the Broadband Router can automatically assign ip addresses.
Prevent Unauthorized bt
Vropat PAT sets the virtual server option to allow Internet users to access services on your LAN. This feature is useful for providing online services such as FTP, Web, or game servers. For each virtual server, you define a public port on the router to redirect to an internal lan ip address and a lanport. Instance: you are running a Web server on a PC with a lan ip address of 192.168.0.50. Your ISP blocks the virtual server named after Port 80 (for ex
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.