domain name packet tracer

Install Cisco Packet Tracer in Linux What is Cisco Packet tracer? Cisco Packet Tracer is a powerful network simulation tool used for Cisco authentication training. It provides us with a good interface view for various routers and

What is Cisco Packet tracer?The Cisco Packet Tracer is a powerful network simulation tool for training in Cisco certifications. It gives us a good view of the interfaces of each router and network device, with many options, and we can use unlimited devices in the network just like with physical machines. We can create

(config-if) #switchport trunk Encapsulation dot1qSwitch (config-if) #switchport mode trunkSwitch (config-if) #no shutSwitch (config-if) #int FA 0/6Switch (config-if) #switchport trunk Encapsulation dot1qSwitch (config-if) #switchport mode trunkSwitch (config-if) #no shutSwitch (config-if) #int FA 0/7Switch (config-if) #switchport trunk Encapsulation dot1qSwitch (config-if) #switchport mode trunkSwitch (config-if) #no shutStep Two: Configuration " Server Aggregation " Switch Trunk Link , Allow V

) # ip nat?Inside inside interface for address translationOutside interface for address translationR1 (config-If) # ip nat inside?R1 (config-If) # ip nat insideR1 (config-If) # exitR1 (config) # int S2/0R1 (config-If) # ip nat outside?R1 (config-If) # ip nat outsideR1 (config-If) # exitR1 (config )#R1 #R1 #R1 # conf tEnter configuration commands, one per line. End with cntl/Z.R1 (config) # Ip?Access-list named access-listDefault-network flags networks as candidates for default routesDHCP configu

on fastethernet0/0 from loading to full, loading doneR2 # Show IP Route // route information after route redistributionCodes: C-connected, S-static, I-IGRP, R-rip, M-mobile, B-BGPD-OSPF, ex-VPN external, o-OSPF, Ia-OSPF Inter AreaN1-ospf nssa external type 1, n2-ospf nssa external type 2E1-OSPF external type 1, E2-OSPF external type 2, E-EGPI-Is, L1-is level-1, L2-is level-2, Ia-Is Inter Area*-Candidate default, U-per-user static route, o-ODRP-periodic downloaded static routeGateway of last res

of last resort is not setC 192.168.1.0/24 is directly connected, fastethernet1/0C 192.168.2.0/24 is directly connected, fastethernet0/0C 192.168.3.0/24 is directly connected, serial/0O 192.168.4.0/24 [110/782] via 192.168.3.2, 00:00:15, serial/0R1 #R1 # conf tEnter configuration commands, one per line. End with cntl/Z.R1 (config) # Ip?Access-list named access-listDefault-network flags networks as candidates for default routesDHCP configure DHCP server and relay ParametersDomain ip dns resolverD

software name : Cisco Packet Tracer 6.2 for Windows Student VersionDownload Link:http://pan.baidu.com/s/1bn2WRmR password: J6JWSoftware:650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/74/FC/wKiom1YwOl6QeNW5AAXqwnnUQnA621.jpg "title=" 1.png " alt= "Wkiom1ywol6qenw5aaxqwnnuqna621.jpg"/>This article is from the "Piece of Cake" blog, please be sure to keep

port to enable ACL policyNetwork topology1, configure Router 1, turn on the single-arm routing configuration subinterface address and connect the physical interface address of another route and open the port2 Configuring the VLAN of the switch, configuring the port type3 Configuring the IP address of the PC, specifying the gateway4 Configuring router static routing to enable network interoperability5 Create a new ACL policy on the destination router6 Enter the destination port to make the new A

Packet Tracer 5.2 Experiment (15) network port address translation NAPT configurationFirst, the experimental target Understand the principle and function of NAT network address translation; Master NAPT configuration, realize LAN access to the Internet; Second, the experimental backgroundCorporate office network needs to access the Internet, the company only applied to the ISP a dedicated l

Tags: cal enhancement packet share image share access Cisco virtual SRCVLAN, the virtual LAN (Virtul local area network), the VLAN divides the physical connected LAN logic into different virtual networks, its existence can reduce the broadcast domain, enhance the network security and convenient and flexible networking, adding PCs and switchesBy configuring VLANs, you can implement PC1 and PC2 that are conne

vty 0 4r1 (config-line) # password ABC123 // set the Telnet Remote logon password r1 (config-line) # loginr1 (config-line) # exitr1 (config) # interface fa0/0r1 (config-If) # IP address 192.168.1.1 255.255.255.0 // configure the management IP address of the router r1 (config-If) # No shutdown // enable port r1 (config-If) # End % SYS-5-CONFIG_ I: configured from console by consoler1 # Iv. PC logon Test Packet tr