easy subnetting

Read Catalogue I. IP Address Basics 1.1 IP Address structure and classification 1.2 special IP address 1.3 subnet mask 1.4 IP address request two. subnetting 2.1 subnetting Concept 2.2 Class C sub-network Division 2.3 subnetting Step 2.4 subnetting Case 2.5 sub-division Network considerations 2.6 Why

IP addresses are classified into five categories--------------------------------------------------------------------------------------------------------------- ----------------------------------------------------the meaning of the subnet mask and subnetting according to the subnet maskThe subnet mask is used to divide subnets. For example, a Class A network can hold 16777214 hosts. However, in practice, it is impossible to use a class A network only f

11111111Example of subnetting:1, a company to apply to a class C IP address, but to connect 6 subsidiaries, the largest one sub-The company has 26 computers, each subsidiary in a network segment, the subnet mask should be set to?A: Assume that the C network address is 192.168.0.0/24,6 subsidiary, namely Divide 8 subnets, two not, each subnet can hold 30 IP192.168.0.0-192.168.0.31/27-255.255.255.224192.168.0.32-192.168.0.63/27-255.255.255.224192.168.0

addresses: "192.168.5.253/30, 192.168.5.254/30"Broadcast address: "192.168.5.255/30"quickly divide subnets to determine IPLet's take example 2 for example:The topic requires that we divide the 192.168.5.0/24 network address into subnets that can accommodate 101/54/2 hosts. Therefore, we need to determine the host location, and then determine the network bit based on the host bit, and finally determine the detailed IP address.① determining the host bitSet the number of hosts that you need to be

LAN.WANThe last network segment is a WAN connection and requires 2 host addresses. Support WAN links with just 2 primary seats. 2^2-2 = 2.This leaves 8 bits to define the local subnet address. The next available address block is 172.16.2.192/30.Address: 172.16.2.192Binary representation:10101100.00010000.0000010.11000000Mask: 255.255.255.252Represents 30 bits in binary:11111111.11111111.1111111.11111100The IPV4 host address range provided is:172.16.2.193 to 172.16.2.194, broadcast address is 17

application, a company applied for a public network, such as 201.1.2.0/24, but the company has two groups, a group of the number of hosts is 6, the number of hosts in the other group is 4, and do not want the two groups of hosts to communicate with each other, if you apply for a public network , the cost is too high, so it is necessary to divide this network into multiple subnets. The subnet is divided by the first m bits in the host bit in the network address and the network address bits as th

mask calculation. Network ID Results We all know that the network ID part is unchanged, the host ID portion becomes 0, then in the calculation of the network ID, first look at how many bits in the subnet mask to represent the network, corresponding to the IP address conversion to binary only the previous few, such as 192.168.176.15/ 19, the network ID altogether 19 bits, then the network ID the first two bytes is 192.168.x.0 to change the third byte. So how do you quickly calculate the value o

subnets will need to occupy 1 bits of the original host identity bit. At this point the network number bit becomes 22 bits and the host label becomes 7 bits. Similarly borrowing 2 host bits can divide a class C network into 4 subnets ... How did the computer know if the network was divided into subnets? This can be seen from the subnet mask. The subnet mask is as 32bit as the IP address, and the subnet mask is determined by using "1" for all corresponding bits that identify the network number i

First, a sample from a Shehiren teacher's book is referenced:Host H1 the process of sending packets to H2:First, with the subnet mask in the subnet:255.255.255.128 and target host H2 IP address:128.30.33.128 and get network number: 128.30.33.128. Obviously this does not match the network number of Subnet 1:128.30.33.0.The datagram is then forwarded by the default route R1 Subnet 1. At this point, R1 will look for its own routing table. Think of the host address and subnet mask of the H2, and whe

Easy language overview --- easy language introduction, Overview --- easy language Easy language Overview 1. Easy language introduction easy language is a self-developed Chinese programming language suitable for national conditions

Import java.util.ArrayList; Import java.util.List; Import Java.util.Scanner; /** * Small easy to have a length of n sequence, small easy to remove the inside of the repeating elements, but small easy to think is for each element to retain the last occurrence of that. Small easy to meet difficulties, I hope you to hel

In daily webpage design, tables are one of the most commonly used html controls. For convenience and beauty, Easy appears. grid, this table is Easy to use, and the symbol is Easy. Users only need to use html and Javascript, and read the Demo of Easy. Grid, and use it freely. If you are a programmer, read the source cod

Address: http://hi.baidu.com/ I _coolboy/blog/item/4ccaf44a965cf42e08f7ef8b.html Next: VMWare easy install mode details: How to enable and disable the easy install mode (image and text)-on Now we know about VMware's easy install mode, so whether or not to enable the easy install mode depends on us. Therefore

In easy language, you can use the "Easy-to-write (exek)" function to develop easy-to-language support libraries. Not only are there no functional limitations, but you can also play with the "Flowers, even the "Flowers" that others cannot play. I. Do not use command Classification Commands in the supported libraries are generally divided into several catego

Easy Language Introduction Easy language is a programming language in Chinese as a program code. Known for its "easy". Founder for Wu Tao. The earlier version of the name is E language. The release of the earliest version of the language can be traced back to September 11, 2000. The original intention of creating an easy