eigrp for dummies

address;6, PC1, PC2 between the host can communicate with each other;R1:650) this.width=650; "src=" Http://common.cnblogs.com/images/copycode.gif "alt=" Copy Code "/>Router>router>enrouter#conftenterconfigurationcommands,oneperline. endwithcntl/z.router (config) #hostname r1r1 (config) #interface fa1/0r1 ( CONFIG-IF) #no shutdown%link-5-changed:interfacefastethernet1/0,changedstate toup%lineproto-5-updown:lineprotocoloninterfacefastethernet1/0, NBSP;CHANGEDNBSP;STATENBSP;TONBSP;UPR1 (config-if)

configuration:Router (config) #hostname R1R1 (config) #inter f0/0R1 (config-if) #ip add 172.16.0.1 255.255.255.0R1 (config-if) #no shutR1 (config) #inter s1/0R1 (config-if) #ip add 192.168.0.1 255.255.255.0R1 (config-if) #no shutR1 (config-if) #clock rate 64000R1 (config-if) #no shutR1 (config) #router OSPF 1R1 (config-router) #network 172.16.0.0 0.0.0.255 area 0R1 (config-router) #network 192.168.0.0 0.0.0.255 area 0routing table for R1:R1#show IP routeCODES:C-connected, s-static, I-igrp, R-ri

router receives a route from OSPF and a route from RIP, it chooses the OSPF route. Because the management spacing of OSPF is 110, the management spacing of RIP is 120. Here's another example: your router receives a route from EIGRP internal, and its management spacing is 90, but you accidentally enter a static route into an IP address where the spacing management address is 1. Then the router uses a static route and does not use

topologyObjectives: Plan, design, and implement the Internation travel Agency core network. Plan, design, nad implement the travel Data Providers Netwrok. Allow the networks to communicate via BGP. Verify that all implementations is operational and functional according to the guidelines. BackgroundThe International Travel Agency (ITA) needs both it core network and its travel Data Providers (TDP) network set up. Configre each network to run

Ting enableR2 (config-if) #int fa0/0R2 (config-if) #ipv6 RIP Ting enablerouting configuration for R3:R3 (config-if) #int fa1/0R3 (config-if) #ipv6 RIPR3 (config-if) #ipv6 rip Hai enR3 (config-if) #int fa0/0R3 (config-if) #ipv6 rip Hai enR3 (config-if) #int Loo 0R3 (config-if) #ipv6 rip Hai enGrasping packet analysis between R1 and R3;650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/58/D4/wKiom1S90OLhFaa-AALC0r9NhjU193.jpg "title=" 1.png " alt= "Wkiom1s90olhfaa-aalc0r9nhju193.jpg"/>gra

sends its entire list. When the neighboring router receives the update message, it copies the contents and sends the information to its neighbor station. There is no need to recalculate the routing table content when it is forwarded. Note that routers using IGRP and EIGRP broadcast Hello messages to discover neighboring stations while exchanging routing update information like OSPF. EIGRP holds a neighbor

172.16.234.20 on Serial0/0 from LOADING to FULL, Loading Done* Mar 1 00:29:11. 151: % OSPF-5-ADJCHG: Process 1, Nbr 172.16.234.40 on Serial0/0 from LOADING to FULL, Loading DoneR4 #* Mar 1 00:29:10. 943: % OSPF-5-ADJCHG: Process 1, Nbr 172.16.234.30 on Serial0/0 from LOADING to FULL, Loading Done* Mar 1 00:29:18. 099: % OSPF-5-ADJCHG: Process 1, Nbr 172.16.234.20 on Serial0/0 from LOADING to FULL, Loading Done 4. R7 cannot form an IPsec neighbor with R8 or R9.Run the show run int S0/0 command o

Open the CD with book 6th practice "06 Publish static routes to dynamic routes. PKT", as shown in Figure 6-22, Hebei Normal University and the Software Institute have their own independent network, there is an independent IT department to manage their own network. Router1 is an export that accesses the Internet. Hebei Normal University's internal network configuration EIGRP protocol, can be considered a homemade system. Software College's internal net

routing R1 Configure static Routes: R1 (config) #ip Route 2.2.2.0 255.255.255.0 s2/0R1 (config) #ip Route 3.3.3.0 255.255.255.0 s2/0 R2 Configure static Routes: R2 (config) #ip Route 1.1.1.0 255.255.255.0 s2/0R2 (config) #ip Route 3.3.3.0 255.255.255.0 s3/0 R3 Configure static Routes: R3 (config) #ip Route 1.1.1.0 255.255.255.0 s2/0R3 (config) #ip Route 2.2.2.0 255.255.255.0 s2/0 3. Experimental test R1: R1#sh IP routeCODES:C-connected, s-static, I-igrp, R-rip, M-mobile, B-BGP D-

), latency (Delay), Reliability (reliability), load (load), etc. but its disadvantage is that it does not support VLSM and discontinuous subnets. IGRP configuration: Router (config) #router igrp 100 (100 is an autonomous system number) Router (config-router) #network Network-number Router (config-router) #exit Attention: 1 The valid range of the number is 1-65535, the number is used to determine a set of regions with the same number of routers and interfaces 2 different numbers of routers

/0.133.0.0.0/24 is subnetted, 1 subnetsC 3.3.3.0 is directly connected, Loopback0\ \ Note the next hop of the route6 EIGRP over Frame-relay650) this.width=650; "title=" clip_image006 "style=" border-top:0px;border-right:0px;background-image:none; border-bottom:0px;padding-top:0px;padding-left:0px;border-left:0px;padding-right:0px, "border=" 0 "alt=" clip_ image006 "src=" http://s3.51cto.com/wyfs02/M00/6E/8B/wKiom1V_hlaxxGEDAABUf5lhq30423.jpg "height="