Web file contenttype type Daquan-from the networkThe ContentType property specifies the HTTP content type of the server response. If contenttype is not specified, the default is text/html.Use it in asp:". *" = "Application/octet-stream"". 001" = "application/x-001"". 301" = "application/x-301"". 323" = "text/h323"". 906" = "application/x-906"". 907" = "drawing/907"". A11" = "Application/x-a11"". ACP" = "AUDIO/X-MEI-AAC"". Ai" = "Application/postscript"". AIF" = "Audio/aiff"". aifc" = "Audio/aiff
32768 K size 1024 blocksize
Loop: loaded (max 8 devices)
Davinci emac mii Bus: probed
MAC address is 02: 00: 10: 00: 00: 00
TI DaVinci EMAC Linux version updated 4.0
I2c/dev entries driver
Nand_davinci nand_davinci.0: Using soft ECC
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB, 3 V 8-bit)
Scanning device for bad blocks
Bad eraseblock 0 at 0x00000000
Bad eraseblock 8 at 0x00100000
, everyone is most concerned with the resource allocation between two cores, communication methods, and how to efficiently achieve resource sharing. ARM exclusive (DSP unavailable) peripherals include: UART0/1/2, I2C, watchdog timer, PWM0/1/2, ARM interrupt controller, USB2.0, ATA/CF, SPI, GPIO, VPSS, EMAC/MDIO, emifa control, VLYNQ, MMC/SD. Peripherals of DSP exclusive (ARM unavailable) include DSP interrupt controller and VICP. Peripherals shared by
]:Internal/external PHY? (e/i) [i]Init EMAC ...Autonegotiation ... successfulMain Menu:==========b) Boot from flashg) Download and run from RAMd) Download and save to Flashe) Erase Flash sectorm) Set modes) Store bootloader parameters to Flashi) Re-init EthernetR) Read MemoryW) Write Memoryj) Jump to arbitrary addressZ) ResetDTFTP Get SelectedBoard TFTP Server IP Address [10.3.45.42]: 192.168.100.2Enter filename [dvb-c8000bg_gd_cm.bin]: ecram_sto.b
)? 2001-2006 Red Hat, Inc.Msgmni have been set to 1009IO Scheduler NoOp registered (default)Serial: 8250/16550 driver $Revision: 1.3 $4 ports, IRQ sharing disabledSerial8250.0:ttys0 at MMIO 0x4ef600300 (IRQ = +) is a 16550Aconsole [ttyS0] enabledSerial8250.0:ttys1 at MMIO 0x4ef600400 (IRQ = All) is a 16550ASerial8250.0:ttys2 at MMIO 0x4ef600500 (IRQ = +) is a 16550ASerial8250.0:ttys3 at MMIO 0x4ef600600 (IRQ = +) is a 16550A4ef600300.serial:ttys0 at MMIO 0x4ef600300 (IRQ = +) is a 16550A4ef60040
revisions, ending in-X or-y set to 0 */
/* When 0, rmii gpio work around is enabled for old Silicon */
6. The core principle of ucosii is to put the highest priority ready tasks in the running state.
Due to sub-restrictions, omitted.
7. Modify
# Define net_sock_cfg_block_sel net_sock_block_sel_block
Is
# Define net_sock_cfg_block_sel net_sock_block_sel_no_block
Sets the socket to a non-blocking status.
It is set to a non-blocking status, so that the webpage can achieve better results in real ti
the search: open and closed. The Open table holds all the nodes that have been generated without being inspected, and the nodes that have been visited are recorded in the closed table. One step in the algorithm is to rearrange the open table based on the valuation function. Each step in this loop considers only the best nodes in the Open table. The specific search process is as follows:1) Initial state:Open=[a5];closed=[];2) estimate the A5, obtain the child nodes, and put into the open table;O
,open firmware parameters and the Macintosh name registry. From another point of view, pram is a small part of the NVRAM.The contents of the data stored in NVRAM and pram vary depending on the model and operating system content. On PowerMac architectures, the content is much more than the Intel architecture. At the beginning of the advent of the Intel architecture computer, the NVRAM was almost empty (at least, I checked it 1.5 ago). And now there's something in the NVRAM in the Intel-architecte
=='__main__': -Sessioncls = Sessionmaker (bind=engine)#create a session with the database sessions class, note that this is a class that is returned to the session, not an instance -Session =sessioncls () in #g1= Group (name= ' G1 ') - #g2 = Group (name= ' G2 ') to #g3 = Group (name= ' G3 ') + #G4 = Group (name= ' G4 ') - #Session.add_all ([g1,g2,g3,
One of the purposes of displaying time in the LINUX command prompt and CMD command prompt is to view the execution time of a command or program. 1. the time setting parameter description is displayed in CMD: $ P: current path $ G: gt; (greater than the number) $ T: current time. The result is accurate to the following: C: one of the purposes that the Usersg4-1016tx shows in LINUX's command and command prompts is to view the execution time of a command or program. 1. the time setting parameter d
computational capacity.Metis's working principle: take K-Way multi-level division as an example.The entire partitioning process is divided into coarsening, initial partitioning and uncoarsening (refinement) three parts. coarsening the size of the graph gradually, g1->g2->g3-g4. The G4 phase is performed in the K-way division, and the original nodes in the diagram are mapped to cluster in the
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.