eth stats

Today, I installed CentOS 6.4 On the Dell R710 server using mini. After the restart, ifconfig can only see one local loopback address. Check the NIC configuration file under/etc/sysconfig/network-scripts/, and the results do not find a configuration file like ifcfg-eth0, but there is more ifcfg-em1 and ifcfg-em2 ..... these configuration files. I did not understand why it became em, so I found some materials. There are two ways to modify the eth form.

===== Centos network interface configuration file ifcfg-eth File/etc/sysconfig/network-scripts/ifcfg-eth0 in/etc/sysconfig/network-script under this directory, store the network interface (NIC) the ifcfg-eth0 is the default first network interface, if there are multiple network interfaces on the machine, then the name will push the ifcfg-eth1, ifcfg-eth2, ifcfg-eth3 ...... (The file here is very important and involves whether the network can work no

The third bomb--the course of digging ore in the ether square First, make sure your video memory is greater than 2GB, which is equal to 2GB. Because of currency restrictions, only 2GB of video memory can be dug. If you don't meet the conditions, you don't have to look at the back. Direct point to the top right corner of the fork off the page on it. Mining software: Http://pan.baidu.com/s/1hsOigq4 This time my tutorial on the short bar, the specific other steps please refer to my two other tut

(if you restart the system, you do not need to manually load)# modprobe Bonding# Lsmod | grep bonding (Verify loading results)Bonding 128245 0Check the status of Bond's NIC after restarting the network service:# cat/proc/net/bonding/bond0Ethernet Channel Bonding driver:v3.6.0 (September 26, 2009)Bonding mode:fault-tolerance (Active-backup)Primary Slave:noneCurrently Active Slave:eth2MII Status:upMII Polling Interval (ms): 100Up Delay (ms): 0Down Delay (ms): 0Slave Interface:eth2MII Status:upspe

Tags: Ubuntu network adapter name ETH kernel configuration fileBy default, the Ubuntu 16.04 system has just been installed and the NIC name defaults as shown.To meet the habit, we changed the NIC name to eth* displayOperation method Configuration file/etc/default/grubGrub_cmdline_linux= ""Switchgrub_cmdline_linux= "Net.ifnames=0 biosdevname=0" Execute the following commandsudo grub-mkconfig-o/boot/

It is often necessary to monitor the running status of memcached on the server, such as the number of cache queries and hit rate. ButThe memcached-tool is written in Perl in Linux, and I have never tried whether it can be used in windows. Later I found a simple method.You can do this by using telnet.First, log on to the server, and then typeTelnet fig 11211127.0.0.1 is the server address (here it is the local machine), and 11211 is the port number bound to memcached.The command line window is bl

Ubuntu configuration ETH nic, fixed IP address1, modify the configuration file/etc/network/interfaces [email protected]: ~# sudo gedit/etc/network/interfacesAdd the following: auto eth0 #设置自动启动eth0接口iface eth0 inet static #配置静态IP address 192.168. 11.88 #IP地址netmask 255.255.255.0 #子网掩码Gateway 192.168.11.1 #默认网关2. Modify DNS sudo gedit/etc/resolve.confnameserver 127.0.0.1 #记得加上nameserver 8.8.8.8 #当地dns服务器 (view local DNS with Ipconfig/all, first DNS is

The Memcached Stats command is useful for viewing the memcache running state. Telnet to the memcached server after a lot of commands can be used, in addition to the well-known add, get, set, INCR, DECR, replace, delete and other assignment commands, there are a series of commands to obtain server information, This part of the command starts with stats. Common commands: StatsDisplay server information,

Memcache monitoring Tool--statsIntroducedMemcache's stats command is the most basic tool for viewing memcache status.Under the default instance, connect to Memcache by using a command such as Telnet 127.0.0.1 11211, and then enter stats to see the current status of Memcache.The descriptions of these states are as follows: Pid Process ID of the Memcache server Uptime Num

About the OGG stats process name reset command, the oggstatsreset command Oracle GoldenGate Command Interpreter for OracleVersion 11.1.1.1.2 OGGCORE_11.1.1.1.2_PLATFORMS_111004.2100 Linux, x86, 32bit (optimized), Oracle 10g on Oct 4 2011 23: 54: 04 Copyright (C) 1995,201 1, oracle and/or its affiliates. all rights reserved. GGSCI (gg321) 22> stats extqd resetSending STA