ethernet 1588

Abstract: In view of the slow transmission speed and difficult network connection of traditional devices, a Data Conversion System for serial ports and Ethernet is proposed using w5300 and c8051f120 single chip microcomputer. the RS232 and RS485 chips are used to receive and send low-speed serial data, the single-chip microcomputer c8051f120 is used as the core processing chip, and the w5300 chip is used to send and receive

Python uses Raw Socket for Ethernet frame injection and pythonraw1. Frame Injection For introduction to Ethernet frames and Raw sockets, refer to a previous blog post that uses Raw Socket for Ethernet frame sniffing. Frame injection features:　　 Packages in the original data format can be injected into the network. It is very powerful in simulating network resp

The principle of automatic Ethernet negotiation and related network test automatic negotiation are one of the most controversial concepts in Ethernet. Is it good or bad? This depends on the situation. When you use automatic negotiation, the supply, driver version, and administrator selection are all considerations. Www.2cto.comWhat is automatic negotiation? Article 802.3 of the 28th standard defines the aut

Ethernet Channel AnalysisEthernet channel ------ it is intended to review previous learning and not to wasteNote Ethernet conditions:1. The member ports must be in the same slot module. 2. The member ports must have the same type (1-gigabit electrical ports, 1-gigabit optical ports, and 10-Gigabit electrical ports) and speed 3. The member ports must work in full duplex mode 4. A maximum of 16 trunks can be

More and more Wan solutions are now using Ethernet overSDH. On the surface, L3 switches and traditional routers can meet the needs of Wan interconnection. Therefore, many partners and customers have this question, what is the difference between the two in the wide area network connection? The following are some of my opinions for your reference.What is the difference between using a Cisco L3 switch and using a router as a WAN connection?First, the net

datagram into a frame format that is suitable for transmission on the physical network, or to unpack the frames received from the physical network and take out the IP datagram to the network layer.5. The physical layer , which is responsible for transferring the bitstream between nodes, is responsible for the physical transmission. The protocol for this layer is related to both the link and the transmission medium.Ethernet FrameSince the physical layer is more related to physical media, the ana

In Solaris, how to configure the fc hba to an Ethernet Card IPFC can easily set a fc hba to an Ethernet card, which is of great significance. In some work sites, if you need to copy a large amount of data through the network, you will often find that the speed of the Gigabit Nic is insufficient, and network aggregation cannot compensate for bandwidth insufficiency, at this time, you can make full use of the

Ethernet II Frame format DA Sa Type Playload Fcs DA (Destination address): This field has 6 bytes, which represents the destination MAC address.SA (source Address): This field has 6 bytes representing the source MAC address.Type: The field has 2 bytes, which represents the type of the packet.Playload: Data payload.FCS (Frame Check Sequence): This field has 4 bytes, which represents the frame check sequenc

Recompile kernel (2.6.29)2.6.29 kernelDevice Drivers---> USB support---> USB Gadget Support--->where USB peripheral controller selected S3C2410 USB Device controllerThen choose a Gadget driver from the kernel to do the demo, here is the Ethernet Gadget (with CDC Ethernet support)Because this driver does not need to pass in the parameters, so give a y instead of M, easyMake and burn zimage to mini1440After t

1. Raw Socket Base Provides a way to bypass the entire network stack traversal and deliver Ethernet frames directly to an application. There are a number of ways to create raw sockets, such as Af_packet,pf_packet. Here you use Pf_packet, which is an option on a Linux system, and if it's a Windows or Mac system, you can use Af_packet. 1.1 Pf_socket Receive and send packets on the link layer to the application interface. A

WIZ550S2E is a gateway module that provides RS-232 to TCP/IP protocol functionality. And can be based on TCP/IP and Ethernet network equipment management, remote measurement, only need RS-232 serial port to connect the current device. In other words, WIZ550S2E is a protocol converter that sends data through the serial port in TCP/IP data format, and vice versa.Characteristics Plug and Play serial to Ether