ex4200

How to implement ECMP function on EX4200First, if the gateway is enabled on the EX4200, EX4200 on two routers, how to implement the link load on the EX4200, so that the packet can be shared on two routers.Second, the specific order is as follows:1. On EX4200: Set policy-options policy-statement lb then load-balance per

the main switch and configure the priority of the primary switch.Four. Configure the out-of-band management address for vme.0.Five. Configure Gres (flat- slip Routing engine switchover )Six. Start the standby switch and configure the priority of the standby switch.We first connect the VC line as required, then start the first switch as the primary switch. The configuration is as follows:A. Primary switch:Set Virtual-chassis member 0 mastership-priority 200Set interface VME0 Unit 0 family inet a

We know that the device at the factory, there is a default administrative user root, the password is empty, this user is not allowed to use our remote login. So we use the default user to enter the device to create a new user as super-user. But the

!! 4960 bytes copied in 1.502 secs (3302 bytes/sec) SW-2960-2 # Iii. ruijie equipment: F1-RJ-S2352G-3 #Copy running-config tftp: Address of remote host []?10.63.201.136// Enter the IP address of your computer Destination filename []?F1-RJ-S2352G-3_20131128// Name the exported configuration file Building configuration... Accessing running-config... Success: Transmission success, file length 3726 You can compare the difference between ruijie and Cisco. When you enter an IP address, you will f

172.16.0.2;} Configuration on CISCO6506:Cs_6506 # interface GigabitEthernet4/1IP address 172.16.0.2 255.255.255.252 Cs_6506 # ip route 172.16.0.0 255.255.255.0.0 172.16.0.1 2. Four aggregation switches (EX4200) in the new network are connected to the core EX8208 and use the OSPF protocol to connect the core EX8208 master) and the four aggregation switches use the layer-3 dynamic routing protocol OSPF. The network architecture is as follows: 650) thi

open. The EX series is designed with flexibility in mind, allowing you to easily add EX series switches to their original network. With the help of conversion tools, users can quickly achieve interoperability. In addition, with the Junos Ready software and equipment provided by Dell, IBM and other partners, users will have more options. In the new data center of Shenzhen Development Bank, Juniper series products including EX8208, EX4200, and EX3200 E

-name EX4200[Email protected]# Delete Host-name EX42003. Set up DNS[Email protected]# set Name-server 192.168.1.1[Email protected]# Delete Name-server 192.168.1.1The [Edit system] display is configured under the System menu and all set parameters are valid for the #system menu4. Set the date[Email protected]# set Time-zone Asia/shanghai[Email protected]> Set Date 200811071441.00 time format YYYYMMDDHHMM.SS5. Set up NTP[Email protected]# set NTP server

Fault resolution: Implementing ECMP functions on the firewall I. Network Topology Ii. basic configuration 1. The Gateway in the workplace is the EX4200 of Juniper, Which is configured with vlan524: 10.63.224.0/24 and vlan525: 10.63.225.0/24. Configure the next hop of the default route to point to the firewall. 2. Two Internet leased lines (China Telecom and China Mobile) are connected on the firewall SSG550-1, and two default routes are configured wi

Bkjia.com comprehensive report] traditional network infrastructure has always adopted a tree structure. the inherent complexity of this architecture greatly limits the performance and scalability required by cloud computing and other IT systems. Therefore, Juniper has been committed to operating multiple devices in the form of a single logical device, thus flattening the network structure and realizing the advantages of such a network architecture. As a leader in high-performance networks, Junip