floppy colon

1. Boot virus capture Virus extraction in the boot area is simple. First, use Format A:/S to copy the boot system file to A floppy disk, and then copy some system execution files from the hard disk to the floppy disk. The specific steps are as follows: Enter the MS-DOS mode, Format A system disk, Format A:/s, for different systems, copy the following files to the same disk: For the gdi.exernl286.exe1_progma

This section describes what happens when a Linux system boots and shuts down, and should be done correctly. If the correct procedure is not followed, the file may be corrupted or missing. Boot and Shutdown overview The process of turning on a computer and causing its operating system to be loaded is called booting. The name comes from a computer pulling itself up to its bootstraps, but the act itself slightly Stic.During startup, the computer first loads a small piece of program called Bootstrap

Boot press F1 How to solve? How to remove Boot press F1? Have you ever encountered, every boot will appear "press F1 to Continue,del to enter SETUP", and then the screen will not jump, must first press the shortcut key F1, the computer can start normally? Boot press F1 fault analysis? Under normal circumstances, require the boot press F1 to enter is the system's BIOS settings have no impact on the system startup of small problems, so first check the BIOS in the hardware information settings a

This section describes what happens when a Linux system boots and shuts down, and should be done correctly. If the correct procedure is not followed, the file may be corrupted or missing. Boot and Shutdown overview The process of turning on a computer and causing its operating system to be loaded is called booting. The name comes from a computer pulling itself up to its bootstraps, but the act itself slightly Stic. During startup, the computer first loads a small piece of program called Bootst

the appropriate display jumper. If there is no display switch on the motherboard, then we should go to the system CMOS settings to change the display type. Message: Press ESC to skip memory test Usually the reason: press the ESC key to skip memory detection. Solution: The machine in every cold start, to detect memory; At this point, if we do not want the system to detect memory, you can press the ESC key to skip this step. Tip: Floppy disk (s) fail C

in with different users and run different programs. Quickly build a user for your family and friends. Second, in Linux, how to use floppy disk, CD and DOS and other non-Linux partitions This is the most asked question for Linux beginners. As everyone has become accustomed to Microsoft's access methods, always want to use similar ideas to find floppy disk and CD-ROM. But in Linux, it follows the way UNIX

of the directory in the tar file. x: Extract the files from the tar file. F: Specify the archive or tape (or possibly floppy) device (typically selected). V: Displays the details of the packaged file, and V is the 1th letter of the verbose. Z: Use the gzip compression algorithm to compress the packaged files. J: Use the BZIP2 compression algorithm to compress the packaged file. 3. Create, view, and extract archive files using the tar command1) An exa

carriage return and then pressing the B key to start Change the password with the password command Nine Insert the system installation CD, restart the machine, start quickly press the DEL key, into the CMOS, the boot sequence to CD-ROM first start, so that the Linux installer started, press F5, follow the prompts to enter Linuxrescue Enter the rescue mode, followed by the choice of language and keyboard, Enter directly, the program tip has installed the Linux system on the har

1. Insert the system installation CD, reboot the machine, press the DEL key when it starts, enter the CMOS, turn the boot order into the CD first, start the Linux installation program, press F5, press the hint to enter the Linux rescue carriage return, enter the rescue mode, and then select the language and keyboard, Direct return, the program prompts you to install the Linux system on the hard drive under/mnt/sysimage, and then the Super User prompt appears. 2, into the hard disk etc directory

00 h-disk system reset 0eh-read sector Buffer01 H-read disk system status 0fh-write sector Buffer02 h-read sector 10 h-read drive status03 h-write Sector 11 h-calibration drive04 H-test slice 12 h-controller Ram Diagnosis05 h-formatted track 13 H-controller driver Diagnosis06 h-format Bad Track 14 h-Internal Controller Diagnosis07 h-formatting drive 15 h-read Disk Type08 h-read drive parameters 16 h-read disk change status09 h-Initialize hard disk parameter 17 h-set Disk Type0ah-read long fan Ar

disk drive can read the traditional "disk, but its access speed is slightly inferior to zip.FDD interface: This is a built-in soft drive interface. It is a traditional soft drive interface that is directly connected to the soft drive interface on the computer motherboard at a low price.A floppy disk is a floppy disk. It is a device that reads 3.5 inch or 5.25 inch flop