This article describes how to configure the IOS Firewall on a Cisco router. What should we pay attention to when configuring the firewall? The following article provides detailed answers.
Pre-configuration on R1, R2, and R3
R1 (config) # int e0/0R1 (config-if) # ip add 172.16.1.1 255.255.255.0R1 (config-if) # no shR1 (config) # ip route 0.0.0.0 0.0.0.0 172.16.1.2 configure Static RoutingR1 (config) # ^
-controller) # linecode ami/b8zs/hdb3 (ami-T1, hdb3_e1)
Router (config-controller) # cablelength short 133/266 (optional, used if the cable length is less than 655 feet)
Router (config-controller) # cablelengh long gain26/-15 (optional, if the cable length is greater than 655 feet, the value is DB gain)
Router (config-controller) # line termination 75-ohm | 120-o
products. In addition, large companies must have their own public IP segments.
Based on the above considerations, I decided to use the IP Network Browser tool for the range of 210. 224. *. 1 ~~~ 210. 224. *. 254 IP segment scan to check whether a network device of a Cisco router or vswitch is used. It must be noted that IP Network Browser is a tool in the SolarWinds Network management software set. It can
Tags: requires domain lock login do not need to enter the password secret process network failure PACExperimental 1:cisco Router base configuration1. Operating mode of the router:Router> user mode, typically used to view statistics, but cannot modify the router's settings.router# Concession mode, you can view and modify the configuration of the
This article will discuss the importance of maintaining the password security of a Cisco router, explain the Cisco router mode, and show readers how to configure five passwords for a vro to protect network security.
Causes of vro security protection using passwords
First, as
With the development of China's routing industry, its market demand is also increasing. As a leader in the routing industry, Cisco routers have a very high market share. Telnet to the Cisco router for remote management is the choice of many network management, but the data transmitted through Telnet is in plain text, so this login method has a great security risk
router configuration mode, enable enhanced IGRP on the networkNetwork specifies a CIDR Block directly connected to the vro.Network-number specifies a directly connected NetworkNo shutdown open a closed Interface
Iii. Start with Cisco router command P:Pad starts an X.29 PAD connectionPermit is used to set conditions for a named ip acl.Ping sends ICMP response dat
kind of configuration can best meet security needs without compromising network performance? This article describes the following parts:
Cisco Router Security Configuration. Password Management
A vro uses a password to prevent unauthorized access to the vro and is a part of the security of the vro. The best way to han
No one liked this, but sooner or later there would be a router crash. All that should be done now is to save the key information in the router memory so as to identify the cause of the router crash and prevent this situation from happening again. To do this, you need to configure the vro to save the core dump information stored on the vro at the time of crash. Ne
the PC: for example, use the TERMINAL program in WINDOWS, use COMl/2, 9600BPS, 8 data bit, 2 stop bit. Others use the default value. After the control port is connected, turn on the power switch of the router.
Initialize Installation
The vro must use a valid power supply. Generally, the zero-ground voltage of the power supply is less than 4 volts, and the zero-fire/ground-fire voltage is 220 volts. Ground Line Protection basically requires that the d
Essential security commands for CISCO router initialization 1. Security Settings for vro Access Control 1. Strict control over the administrator who can access the vro. Record Filing is required for all maintenance tasks. Www.2cto.com 2. do not access the vro remotely. Even if you need to access the vro remotely, we recommend that you use the access control list and high-intensity
Introduction to CISCO router AAA and related routing configuration cisco aaa www.2cto.com 3A concept: authentication authorization Accounting accountingcisco provides a variety of 3A services for routers and switches: 1. Self-contained AAA router/NAS self-contained AAA service NAS (Network Access Server) 2. Contact the
Line Protection basically requires that the devices connected to the internet have a ground line, including hosts, workstations, hubs, switches, routers, and MODEM connected To routers. A terminal or PC configured with a Cisco router must also use a valid power supply. Cisco synchronous serial interfaces are commonly used. Different interfaces can be obtained th
privileged mode, you must set a privileged mode password or configure telnet user rightsConfigure the Vty line login password and enable global password encryptionLog on to the router with the Telnet command to seeDisplay current configuration informationPC0 setting 192.168.1.2255.255.255.0192.168.1.1Router0 configura
network will be fatal. Therefore, to improve security, the Cisco router sets password management for the Auxiliary port. Therefore, it is recommended that the network administrator do not use the same password as other passwords in password settings. Otherwise, the security
As a port device connecting WAN, vrouters have been widely used. Their main function is to connect multiple independent networks or subnets to achieve optimal routing and datagram transmission between the Internet. This article takes the Cisco 2511 vro as an example to introduce four router configuration methods.
1. Use the Cisco
, a PPP frame on its hardware chip can be used to eliminate the overhead of the router's central processor. This feature ensures that the router maintains a high-speed connection over all asynchronous ports at the same time. This is useful in actual management. Especially when several network management experts jointly discuss network faults, the value will be reflected.
However, although secondary ports are used as Asynchronous ports, they cannot ach
access a vro, further configuration is required to restrict further access to the vro.
Most Cisco routers are still controlled through remote logon and do not adopt any encryption method. Communication Using Remote logon is transmitted in plain text, which easily exposes the logon password. Although CiscoIOS12.1 adopts the SSHl encryption method, there are still many problems. Before
(you can also use the enable serect "changepassword" command to change the superuser password ). (6) type the following command to restore the original register: "Router (config) # config-reg 0x2102"; "Router (config) # ctrl-z "; "Router (config) # wr" storage disk. (7) restart the vrouter to "
services such as BIND, IMAP, POP, and sendmail, which are frequently problematic in UNIX systems. Although there are few ways to access a vro, further configuration is required to restrict further access to the vro.
Most Cisco routers are still controlled through remote logon and do not adopt any encryption method. Communication Using Remote logon is transmitted in plain text, which easily exposes the logon passw
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.