gateway computer recovery disk

U disk in our daily life is more and more, but sometimes u disk is likely to infect the virus or appear so that the fault, so that the time to do a U disk data backup becomes very important. There are many methods of data backup, the following describes a commonly used USB disk data backup and

Step 1. Enter the Samsung recovery Solution5 software Boot when the Samsung screen is pressed F4, enter the Samsung recovery solution 5 software, select the Restore option. Step 2. Go to restore option Click "Full Restore", select the backup point, and click "Next". Step 3. Start restore The screen shows "Do you want to start the restore?" ", select Yes."

Problem My unit has an IBM DS400 disk array, received an IBM server, from my computer can see that there are two large-capacity partitions, but once in a while (may be a power outage), do not see one of the large capacity partitions, suspected of a set of arrays dropped. Start the server with ServeRAID 7 and view the results as shown in Figure 1234, prompting the "identify physical drive 1" operation for

clear pause, when the above problems, you should look at the DMA mode of your hard disk is not by the Windows system itself shut down. To see if your system turns on DMA mode: A. Double-click Administrative Tools, and then double-click Computer Management; B. Click System Tools, and then click Device Manager. C. Expand the IDE ATA/ATAPI controller node; D. Double click on your "Primary IDE controller";

interface and cannot start the computer. Here is the problem. Let's modify this file. You can refer to the boot. ini configuration file of another computer to modify it. After modification, the correct boot. ini configuration file: www.2cto.com [boot loader] timeout = 3 default = multi (0) disk (0) rdisk (0) partition (1) /WINDOWS [operating systems] multi (0)

Knowledge Point Analysis: Use the backup file under the Lenovo Rescue system, one key recovery Operation Steps: Step One: Backup important files in C disk Back up the C disk of important files and data to other disk characters, in case of a key to restore data loss caused you to lose. Restart your

SuSE system disk File corruption recovery I came by this morning and found that the development machine could not even be caused by a power outage over the weekend. Boot, but found the machine can not start. Www.pcjsh.com Access to rescue (FAILSAFE) mode detection problem, found because the/DEV/SDA4 partition appears file system corruption. /dev/sda4:unexpected Inconsistency:run fsck manually. (i.e. with

1, the newly bought U disk plug computer did not respond, whether it's a front chassis or a USB port behind the chassis, consider the reason there are two points, one is the U disk is bad, this situation is relatively small, because the formal manufacturer in the U disk production will be tested once, unless you buy fa

connected to the computer on the U disk or card reader to unplug and then restart can solve this problem, the solution is to boot press F2 into the BIOS, in the boot device sequence, the CD-ROM drive, hard drive set in front, and the U disk startup (USB-HDD) Adjust to the back, after setting must remember to press F10 save will be effective OH. Troubleshooting:

drive data cable is not connected, if all connected, and then check the Blos to disable the optical drive. If you don't have the above 2 questions, the CD drive is broken. need to buy again. 　　Other attempts: 1. Try the other discs to see if they are not possible 2. Check whether it is a CD-ROM, but you put the DVD disc in, is not a good 3. If not yet, no warranty will go to the warranty First check my computer to show the CD drive letter does n

= Save to Side 0 Cylinder 0 Sector 1!!! ”。 At this point, click the "F9" key, you can just find, that is, in the table shown in the original hard drive main information, covering the hard disk 0-face 0 pillars 1 sectors, and then the machine will reboot the hard disk, restore the starting performance of the hard drive. Second, of course, it may also be a hardware failure, for example, the

Files deleted on the computer, usually, if not specially handled, the system simply deletes the file name in the allocation table, and the real data is still on disk. With some data recovery software, it's easy to recover files that have been called deleted. The partition assistant has the ability to erase the disk, i

One, USB is not recognized by the computer, if the system or system with the driving reasons, you can repair the following methods: 1, the boot press F8 into Safe mode after the exit, select Restart or shutdown in the boot, you can enter the normal mode (repair the registry). 2, if the failure is still, please use the system with the System Restore, restore to you did not appear this time of failure repair (if normal mode

because of the recent Oracle project, you need to put the database in another computer to configure the same database to test the development, before the use of MSSQL, only need to attach or restore the line,But in Oracle, it's not that simple, but it's not that hard, but the operation is as follows:1. Inside the server computer: Start-run-cmd and then go to a relatively large

u disk only by inserting the computer can query u disk data file, but recently a friend in the use of U disk, U disk how also not connected to the computer, this is how it? USB disk can

What are the solutions to the hard drive problems? 1, the hard drive finishing, in defragmenting the hard disk, remember to close all other applications, including screen saver, it is best to set the size of virtual memory to a fixed value. Do not read and write to the hard disk, once the collation found that the hard disk files have changed, it will restart the

I have checked a lot of articles on installing multiple systems on the Internet. Almost all articles say that only two different versions of systems can be installed (such as service2003 and XP, XP and win7) or a Linux system can be added at most. This is not the case. As long as your hard disk is large enough, how many systems can be installed in each partition (it seems that at least one is not a win7 system ), is it necessary to decide on your own

also be a self-test every time, to think of the computer long self-test, very simple, if it is a 2000XP system, as long as the run: Chkntfs t:0 chkntfs X C: OK Chkntfs t:0 Set the self-test wait time to "0", and of course you can customize the wait time Chkntfs X C: Can cancel the boot on the C disk automatically scan, can also be changed to another disk 2. H

the shutdown application and then cut off the power of the time will often occur, we may be in many forums and newspaper questions and answers column, all see the question " Why the soft shutdown when the "problem"-at this time the hard drive reset action is probably not completed, if the user uses forcibly cut off the power of the practice, hard disk physical damage is a great possibility. * Correct approach: If the soft shutdown when the crash, sh

Computer algorithms: The process of converting input into output as needed in one stepOh,no!You should first describe the data store and store it on disk:Data storage for computers: Usually our computers operate in 10 binary, such as: 4, and the computer is calculated by means of 2 binary: for example2 The internal ID of the computer is: 0010Since it is 2 binary,