how to configure router to use wpa2

Many users are not particularly familiar with vro configurations, so such errors often occur during use. The following describes the IOS configuration locks in vrouters, prevent router configuration errors. If multiple network administrators connect to the vro at the same time to modify the configurations, the changes may be lost or only part of the content can be executed, resulting in problems in the oper

Use the tftp function of Linux to configure information about cisco router-Linux Enterprise Application-Linux server application. The following is a detailed description. In a LAN environment, if there are Cisco routers and Linux servers. Maybe you need to use Linux The TFTP service downloads the Cisco

Experimental topology Router (config) #frame-relay switching to simulate a router as a Frame relay switch Router (config) #inter S1/1 Router (config-if) #clock rate 128000 Router (config-if) #encapsulation Frame-relay Configuration Interface encapsulation and binding r

transmission.　　· Dynamic RoutingSome computers support dynamic RIP routing to find routers. The disadvantage of this method is that the conversion between the primary router and the backup router is slow. The above three methods are mainly used on the computer side. The Cisco router provides the HSRP technology, which does not require any computer settings, the

This article uses a specific example to illustrate how to configure the access to ADSL through the vro. What problems should we pay attention to during access? The following articles will benefit you a lot. Note: In this case, a common adsl modem and a cisco 25001841) router (dual Ethernet port) and IOS 12.2 (15) T need to be used to connect to the China Telecom adsl PPPoE, able to achieve LAN Internet shar

The slow speed of wireless networks and unstable signals are widely recognized as drawbacks. In fact, the actual situation may not be a problem with the network itself. Have you checked whether the parameter settings of your hardware device are correct? Follow this article to see the correct process of configuring a wireless router. I believe that after reading this article, you must be able to configure a

Vro setting virus blocking measure 2 (1) Port reinforcement The setting of the password is of course very important if you want to make sure that the wall of the router is solid. Generally, the network administrator can log on to the vro through the Console Aux and Ethernet ports of the vro and then configure the vro. This situation makes management easy, but illegal users can also access it through virtual

If your home is dial-up Internet users, even if the new fiber-optic households, you must remember to dial the Internet account and password Oh. Fiber-optic Connection router specific steps: 　　First, the household fiber connectivity, using a network cable will be the router's WAN port and Light cat (fiber box) LAN port, we see the router's WAN lights flashing, indicating that the connection is normal. 　　Second, start setting up the

Access is a very safe way to secure your data. Through its encryption, each data packet transmitted between your wireless router and your wireless network adapter will be packaged and encapsulated by a different key. This means that even if someone intercepts your data packets and cracks the encrypted string, they cannot read other data parts. Because the same encrypted string duplication is unlikely. Now some of the latest wireless routers have star

configure the wireless router for each layer. In practical applications, the coverage of indoor AP can only be up to 30 meters. 802.11b actual use rate is only about 40% of the nominal value, the conversion rate of data transfer is about 600KB/S, if set to 64/128-bit WEP encryption, transmission rate will be further reduced, so

available network, and if there are no other wireless network nodes nearby, you should list only one network, or else you will be able to include other nearby wireless networks. Next Click "Properties" to activate the "Data encryption (WEP enabled)" Item. Then, in the following "network key" and "Confirm network key" two columns to fill in the encryption string just set, and then click "OK", the wireless network adapter can be connected to the wireless network node correctly. Five, experien

(laptop, smartphone, iPod Touch, iPhone, Zune, netbook, wireless printer, etc. After these devices connect to the virtual router, they can achieve the same effect as they connect to other available WiFi hotspots, and the wireless connections between them are encrypted with wpa2 (the most secure wireless encryption. [Virtual router software] Virtual

Router tplink882 Configure the wireless bridging method: Primary and secondary routers through the wireless WDS Bridge, wireless terminals can connect the main and secondary routers online, mobile process can be automatically switched to achieve roaming. The topology is as follows. To confirm the wireless signal name, wireless password, and wireless channel of the main

routera>en herePassword:！ Prompt for privileged mode password, enter star hereRoutera#en！ Telnet to router A for configurationroutera#Routera#conf TEnter configuration commands, one per line. End with cntl/z.RouterA (config) #exitroutera#routera#Routera#exit！ Use the exit command to exit Telnet loginThe above steps can be operated from another machine, the figure is as follows: 650) this.width=650; "Src="

address 192.168.1.X (X is a natural number ranging from 2 to 254)◆ Subnet mask 255.255.255.0◆ Default Gateway 192.168.1.1 Why is the above parameter? For WR541G, The R460 LAN port IP address is its default gateway address! However, before configuring the WAN port, you need to change the IP address of the WR541G LAN port, because the default IP address of the wr541.1 LAN port is 192.168.1.1 by default to avoid conflict. The change process is as follows: first,

vro console, other users can access the user mode. If you do not set a password for other modes, others can easily enter other modes. The Console port is the place where the user first sets the new router. It is extremely important to set a password on the Console port of the vro, because this prevents others from connecting to the vro and accessing the user mode. Because each vro has only one console port, you can

to integrate the ADSL account into the router. Click the "Homepage" tab on the top, and then click "WAN" as the change. In PPPoverEthernet, you can see the place where the ADSL account is set. Enter the applied ADSL account and password and save the settings. Now, go to the "System Information" section in the "system status" tab to check the network status. On the WAN side, you can clearly see the network information obtained by ADSL dialing. After c

"Experiment Name"Configure Telnet on the router."Experimental Purpose"Learn how to configure Telnet on a router to enable remote login access to the router."Background description"When routers are used to connect multiple subnets, the placement is usually far apart, and it i

step. Basic configurations of a cisco router: Cisco IOS Software Overview Configure a Cisco router for the first time How to connect to the control port of a cisco Router How to set the cisco router Host Name How to enter the cisco rout