how to enable port on cisco switch 2960

Note: Each interface supports only one policy, and one policy can be used for multiple interfaces. Therefore, the download rate limit for the network segment under the port should be defined in the same policy 1. Start QoS on the switch Switch (config) #mls QoS//Start QoS on the switch 2. Define Access Control List

Microsoft's Windows Server 2012 has been able to support LACP link aggregation, due to the use of link aggregation can achieve line redundancy and bandwidth increase, here I used a Cisco 2960 to do a test for interested friends reference.Experiment Preparation:Cisco switch 29,601, install server 2012 servers, there are two Gigabit network card, network cable two

Cisco 2960 Switch Configuration1. Cisco Working mode classification and function#用户模式仅答应基本的监测命令, the configuration of the router cannot be changed in this mode.Switch> #用户模式#允许用户执行所有的测试, view, save and other commands, this mode can not be modified router configuration, generally this mode is recommended to set password

1. Start the QO on the switch SMLS QoS2. Defining access Control ListsAccess-list deny IP 192.168.0.0 0.0.255.255 192.168.0.0 0.0.255.255 #拒绝的网络段Access-list deny IP 172.0.0.0 0.255.255.255 172.0.0.0 0.255.255.255 # denied network segmentAccess-list deny IP 10.0.0.0 0.255.255.255 10.0.0.0 0.255.255.255 # denied network segmentAccess-list deny IP host 192.168.1.1 # # rejected hostsAccess-list permit ip any 192.168.1.0 0.0.0.255 #下载的网段Access-list Permit

1. Experimental topology650) this.width=650; "Src=" https://s4.51cto.com/wyfs02/M00/97/B2/wKiom1kxPDizomXqAABw1vEUgaA990.jpg-wh_500x0-wm_ 3-wmp_4-s_3605733301.jpg "title=" rspan.jpg "alt=" Wkiom1kxpdizomxqaabw1veugaa990.jpg-wh_50 "/>2. Switch configuration4F-IDC-01 ConfigurationVLAN 100Remote-spanMonitor session 1 Source VLAN 13Monitor session 1 destination Remote VLAN 1004F-IDC-04 ConfigurationVLAN 100Remote-spanMonitor session 2 Destination interfac

(config) #no monitor session 1Switch (config) #endSwitch#wrSwitch#show MonitorNo SPAN configuration is present in the system.3. Other(1) Port image filtering, port mirroring can do filter.Monitor session session_number Filter VLAN Vlan-id [, |-]* * Specifies which VLANs belong to the traffic that the source port is entering, and can be emitted from the destinati

: On the emulator, you cannot use the show port-security command on a layer 3 switchPC Settings 192.168.1.2//pc0192.168.1.3//pc1192.168.1.4//pc2192.168.1.5//pc3//Subnet mask and gateway 255.255.255.0 192.168.1.1PC (Command prompt cmd) ipconfig//view MAC address of 4 PCs separatelySwitch0 configuration switch>enswitch#conf tswitch (config) #inter rang f0/1-22switch (config-if-range) #switchport mode access/

The implementation of the multi-port Cisco switch module is a common problem. How to configure the Cisco switch module, any problems related to ports will be fully resolved in this article. Cisco

continue tracing as follows: Ipv9se> (enable) show cdp nei 3/11*-Indicates vlan mismatch.#-Indicates duplex mismatch.Port Device-ID Port-ID Platform----------------------------------------------------------------------------3/11 Cisco2924 GigabitEthernet1/1 cisco WS-C2924M-XL This command shows that the Peer device is a Cisco2924 device. If it is not displayed,

The port rate between switches and switches, between switches and routers, does not meet the actual rate and requires tying more than two ports together to load balance and prevent single points of failure.1. Select Switch SW2960 to configure the F0/1 and F0/2 port modes to truck#conf Terminal into privileged mode#interface Range Fa0/1–2 used to bind a set of po

I will talk about two tips, one about monitoring switch port traffic and the other about store value. 1. Monitor switch port traffic Switch monitoring document in the production environment on the Internet. Therefore, it is complete, and a key knowledge is interspersed in th

operations on core commands, let's talk about port security operations: first, disable port 3. Use the switchport mode access command to configure the port as the access port for port security configuration. Run the switchport port