These days, when HP acquired H3C, it was rare to see 3COM with 3 O-markers. But the problem, a year ago a project bought a 3COM switch 2924-SFP plus switch (PS: pure switch, no readable data). At that time saw a default management
Huawei 3COM high-end switches are described in detail, including software platforms, management methods, and subjective feelings. I have asked many people and have no satisfactory answers. Below is a similar answer to the question found on the Internet.
Software Platform
Compare Huawei 3COM high-end switches with Cisco switches, that is, the comparison between Cisco proprietary technology and industrial sta
3COM in a very strange way to maintain the equipment they sold, that is the backdoor password, any of the following passwords are the highest permissions, you can set the device freely.
Corebuilder 6000/2500-username:debug password:synnet
Corebuilder 3500 (Version 1.0)-Username:debug password:synnet
Corebuilder 7000-username:tech Password:tech
Superstack II Switch 2200-username:debug password:synnet
Su
A few days ago, Huawei 3Com launched a new switch-Quidway®S3100 series Gigabit smart Ethernet switches. This series of products is available in the original Huawei 3Com Quidway®Based on the S2000/2100 series, a new generation of products that further improve forwarding performance and various business indicators, its superior product performance, complete securit
Default 3com bay switch vro account and password
Information Source: Niu Ge3COM maintains the devices they sell in a strange way. Any of the following passwords are the highest permissions and can be set freely.CoreBuilder 6000/2500-username: debug password: synnetCoreBuilder 3500 (Version 1.0)-username: debug password: synnetCoreBuilder 7000-username: tech password: techSuperStack II
Pay special attention to the PVLAN configuration steps and precautions of the Huawei 3COM Switch. There are many articles about the configuration. You should pay more attention to the precautions related to the PVLAN configuration of the Huawei 3COM Switch during configuration, pay attention to it.
Introduction of PVLA
When configuring the HP switch, connect to the Console line of Cisco directly at startup, with the default baud rate. However, the command line does not display anything, so I thought the machine was broken and I changed several, the baud rate has also changed a lot. I also asked a senior network engineer, later, when I tested the brocade switch, a customer asked
Dual-host switch (NewStartHA, SKYbility, hacmp, hp unix dual-host), hpux dual-host
1. Suse linux (NewStartHA ):#
Cli
Cli: ~>Service-migrate
Select service to migrate:
Current service:
0) bill
1) gdb
2) cancel
Select a service [0, 2]:
Enter the command line prompt for replacement.
2. AIX (HACMP ):
# Smit hacmp
Then enter:
Switch the resource from suibao01 to suib
1. Configure www.2cto.com for the HP Server1. Start> Control Panel> HP Network 2. Select two NICs and click Team3. Click Properties 4. Start with switch 5. Server Load balancer, select Auto www.2cto.com 2. Configure the H3C switch www.2cto.com[DeviceA] vlan 10[DeviceA-vlan10] port gigabitEthernet 1/0/1[DeviceA-vlan10]
Specific steps to execute the factory default reset on the switch are:1. Using a small, thin tool with blunt ends (such as a paper clip), simultaneously press both the Reset and Clear buttons on The front of the switch.2. Continue to press the Clear button while releasing the Reset button.3. When all three Mode LEDs (ACT, FDx, and SPD) begin to Blink, release the Clear button. The
This article is from the original blog of Lao Niu. Address: Ghost
This article is from the original blog address of Lao Niu:Http://www.cnpublic.com/2009/08/hpnotebook-Ubuntu-wlan-led/Reprinted please note
Today, I used my Hp notebook to wirelessly access the internet. I found a strange problem, that is, the wireless Nic switch at the Palm has been flashing after network connectivity, and it is red when it
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.