hp switch vlan

Lab name: Use a layer-3 Switch to implement communication and rip routing between different VLANs Tutorial topology: 650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M02/45/E0/wKioL1Psz8jTvsBfAAC_AZ6gzgI409.jpg "Title =" image007.png "alt =" wkiol1psz8jtvsbfaac_az6gzgi409.jpg "/> Tutorial steps: (1) first configure the VLAN for the switch, and then assi

China 3 layer Switch VLAN isolation192.168.1.0---------g1/0/1 S SW g1/0/2-------192.168.2.0192.168.3.0-----------------------|192.168.4.0-----------------------|Prohibition of 1.0, 3.0, 4.0 and 2.0 visits[H3c]acl Num 3000[H3c-acl-adv-3000]rule deny IP source 192.168.1.0 0.0.0.255 destination 192.168.2.0 0.0.0.255//Forbidden 1.0 Access 2.0[H3c-acl-adv-3000]rule deny IP source 192.168.3.0 0.0.0.255 destinatio

Route Use sub-interfaces Configure fa0/0 with no IP address and activate Interface fastethernet0/0 No IP Address No shut Configure sub-interface 1Fa0/0.1 Interface fastethernet0/0.1 Encapsulation dot1q 2 (vlan2) IP address 10.10.10.1 255.255.255.0 No shut ConfigurationSub-interface 2Fa0/0.2 Interface fastethernet0/0.2 Encapsulation dot1q 3(Vlan3) IP address 255.255.20.1 255.255.255.0 No shut SW Configuration: Create vlan2 and vlan3 VLAN Database

directly switch from one port to another. R0 (config-if) # ip add 1.1.1.1 255.255.255.0 R0 (config-if) # no shut // you do not need to configure the frequency here. One CIDR block is enough. R0 (config-if) # exit R0 (config) # ip rout 10.10.10.0 255.255.255.0 1.1.1.1 The configuration of S2 is as follows: S2 # conf ter S2 (config) # int vlan 1 S2 (config-if) # ip add 10.10.10.100 255.255.255.0 S2 (config-

Add acces to the VLAN:Sysint G0/0/1Port Link-type ACCPort default VLAN 2To add a trunk type to a VLAN:Sysint G0/0/1Port Link-type TrunkPort Trunk Allow-pass VLAN 2To create a single VLAN:SysVLAN 2Description XXXBatch Create VLAN:SysVLAN Batch 2 to 10Configure the traffic statistics feature for VLANs:VLAN 2Statistic enableThis article from the "Small Sky" blog, reproduced please contact the author!Some confi

1. Configure www.2cto.com for the HP Server1. Start> Control Panel> HP Network 2. Select two NICs and click Team3. Click Properties 4. Start with switch 5. Server Load balancer, select Auto www.2cto.com 2. Configure the H3C switch www.2cto.com[DeviceA] vlan 10[DeviceA-vlan10

When configuring the HP switch, connect to the Console line of Cisco directly at startup, with the default baud rate. However, the command line does not display anything, so I thought the machine was broken and I changed several, the baud rate has also changed a lot. I also asked a senior network engineer, later, when I tested the brocade switch, a customer asked

new administrator password:New Administrator Password accepted. > System # apply> System # Save Remember to use apply to make the configuration take effect every time you change it. To ensure that the configuration will continue to take effect after restart, you must save it! Network Configuration: port 21 is uplinked to core 1 and port 22 to Core 2. Therefore, you need to add this port to all VLANs and enable tags on the uplink port. No tags are required for all downlinks. Configure Ports 21 a

; system# Save Remember that every time you change the configuration, you must use apply to be effective, in order to ensure that the restart will continue to take effect, must save! Network configuration, 21 ports top to core 1,22 port allied to Core 2, so to add this port associated to all VLANs, and on the upper port to enable tag, all downlink do not need tag Configure 21 and 22 ports for tagged Configuration Command Cfg→port 22→ena→cur→tag e→apply→save→cur Configure 21 and 22 ports to

Dual-host switch (NewStartHA, SKYbility, hacmp, hp unix dual-host), hpux dual-host 1. Suse linux (NewStartHA ):# Cli Cli: ~>Service-migrate Select service to migrate: Current service: 0) bill 1) gdb 2) cancel Select a service [0, 2]: Enter the command line prompt for replacement. 2. AIX (HACMP ): # Smit hacmp Then enter: Switch the resource from suibao01 to suib

This article is from the original blog of Lao Niu. Address: Ghost This article is from the original blog address of Lao Niu:Http://www.cnpublic.com/2009/08/hpnotebook-Ubuntu-wlan-led/Reprinted please note Today, I used my Hp notebook to wirelessly access the internet. I found a strange problem, that is, the wireless Nic switch at the Palm has been flashing after network connectivity, and it is red when it

Specific steps to execute the factory default reset on the switch are:1. Using a small, thin tool with blunt ends (such as a paper clip), simultaneously press both the Reset and Clear buttons on The front of the switch.2. Continue to press the Clear button while releasing the Reset button.3. When all three Mode LEDs (ACT, FDx, and SPD) begin to Blink, release the Clear button. The