Typical routing methods include Static Routing and dynamic routing.
Static Routing is a fixed route table set in a vro. The static route does not change unless the network administrator intervene. Because Static Routing cannot reflect network changes, it is generally used in
Source: Http://insp.top/learn-laravel-middleware-routegroup
The previous section describes the basic usage of Laravel routing, and now we want to learn more about what is on the route.
This article contains the following subsections, and it is recommended to read the official documentation before reading. Middleware routing Groups
Middleware
In the official document, this part is behind the route, but I wan
Network Layer Routing and Application Layer Routing In the IP connection network, the correct communication between hosts is ensured by the correct routing. Here, the routing is not a hardware router, but a routing policy. First, summarize the
today will bring you a new technical introduction series, the name of this series is called "Routing technology in the enterprise's specific application" This is the first article series, "Static routing, default route NAT and static floating routing "I think when you see these nouns, you will not be unfamiliar, whether you are learning Cisco Certification syste
This article discusses the routing subsystem of IPV4. (The IPv6 is different from the routing process).Basic conceptsThe routing subsystem works on layer three, which is used to forward ingress traffic.The routing subsystem mainly designs routers, routes, routing tables and
Routing protocol is divided into static routing protocol and dynamic routing protocol. There are many kinds of dynamic routing protocols, such as RIP, OSPF, EIGRP, and so on.1. RIP (Routing Information Protocol) is the first open standard used between router manufacturers. R
This article is mainly about the addition of static routing table, and how to let you do not have access to the Internet host through the Firewall routing table to achieve the function of the Internet.Static route table:If your host is 2 network card, and do a network card binding, according to my method below is not successful, you can go to edit:# vim/etc/rc.d/rc.localIP route add 12.0.0.1/24 via 192.168.
In general, we can get an application based global routing table through the static properties of routetable routes, which we know is a kind of routecollection collection object. We can route the map by calling its Mappageroute, which is the matching relationship between the registered URL template and a physical file. The core of route registration is to add a route object to the Global routing table, wher
Previous: static Router
DynamicRouting ProtocolFeatures
1) the dynamic routing protocol can automatically update its route table and send updated messages to other dynamic routing protocols it knows.
2) the purpose is to manage the work of the network administrator.
3) There must be a routing protocol suchRIPOrOSPF.
RIP route information selection Protocol
RIP is
For a self-organizing network, the routing protocol of the eighth version is a key and difficult point. So today we will discuss some of the issues of this agreement, and here we will give you a closer look. The content of this article is as follows: Research on the routing black hole attack problem of the routing protocol in the Ad-hoc network, based on the idea
Introduction to thinkphp routing mechanism, thinkphp routing mechanism
The example in this paper describes the thinkphp routing mechanism. Share to everyone for your reference, as follows:
Thinkphp supports the URL routing feature, you need to set the router_on parameter to true to enable
1. static IP routing 1. 1. A simple route table
Routing is one of the most important functions of the IP layer. The previous section briefly describes the rules used by the router to select a route based on the IP address of the IP packet. We will not repeat it here. First, let's look at a simple system route table.Destination gateway genmask flags metric ref use iface
192.168.11.0*255.255.255.0 u 0 0 0 eth
Route Description:What is routing:
Routing is the path, refers to the router after receiving the IP packet, to find out the routing information from the process of forwarding.
The routing information is a message to the destination, which indicates the direction of the destination, and usually the
In routing failures, downstream devices cannot learn to troubleshoot multicast routing on the router as follows:
Network environment
Multicast data is forwarded to the Routera,routera on the vlanif port to terminate the VLAN information of the multicast source through two layers, all three-layer interfaces (both physical and logical) enable multicast protocol IGMP and PIM SM, and the device Routerb IGP ro
This article contains the following sections, which are recommended to read about the official documentation section before reading.
Middleware
Routing groups
Middleware
In the official document, this part is behind the route, but I want to move it to the front, which is more reasonable.
What is this?
We know that routing is a process that parses requests from clients and distributes them to the appr
Many people may not have a special understanding of the routing protocol of the sensor network. The following describes the routing protocol of the sensor network. With the development of communication, computer, network, information processing, sensing, and other technologies, we have been able to produce intelligent micro-sensors with fine, low-cost features such as sensing, information processing, and co
Many people may not know much about the OSPF routing protocol. Here we will mainly explain the detailed introduction of the OSPF routing protocol. Here we will share it with you and hope it will be useful to you. Link State packet type in the region:
1. Router LSA
It is generated by all vrouters in the region and can only be broadcast in flood scenarios in the region.
2. Network LSA
Generated by the DR or B
There are many applications for dynamic routing and Static Routing. Here we review the development history and future directions of Dynamic and Static Routing. The previous lecture on VPN routing and forwarding focuses on configuring and verifying VRF (VPN route forwarding. In the above circumstances, users must be iso
The Magento routing system requires two layers of abstraction to be considered.1, first you need to understand that there may be countless multiple routing objects that are responsible for handling routing logic, and finally only one routing object can get and process the request. By default, Magento has four route obj
URL Routing (Routing) has two main uses in ASP. NET MVC, one purpose is to match the HTTP request from the browser, and the other is to respond to the appropriate URL to the browser .3.1 Matching HTTP requests coming through the browserFirst, let's take a look at the first use, which is to match the HTTP request coming from the browser.When a client makes a request to an ASP.
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.