FSMC full Name "Static memory controller". With the FSMC controller, the fsmc_a[25:0 provided by FSMC can be used as the address line, and the fsmc_d[15:0 provided by FSMC] as the data bus.(1) When the storage data is set to 8 bits (fsmc_nandinitstructure.fsmc_memorydatawidth = fsmc_memorydatawidth_8b)Address fsmc_a[25:0], data bit corresponding to fsmc_d[7:0](2) When the storage data is set to 16 bits (Fsmc_nandinitstructure.fsmc_memorydatawidth = fsmc_memorydatawidth_16b)Address fsmc_a[24:0],
1. Do not use LCD for 24 hours uninterrupted
Many users believe that in the process of using the LCD is smaller than the CRT, but also to save electricity, so often 24-hour uninterrupted rest of the use of LCD monitors. In fact, this approach is wrong. LCD in the continuous high-intensity work 48 hours later, its agin
1. FIMD Structure Block diagram(1) Samsung's s5pv210 LCD controller is called FIMD (also known as Display Controller). Display controller, which includes the image data from the Camera interface controllerThe ground bus or in the system storage the video buffers in the storage (for example, memory) are transmitted to the external LCD driver interface logic. LCD d
This article is good and can be used to get started with FSMC ..
LCD has the following control lines:CS: Chip Select, effective at low levelRS: Select the Register Select RegisterWR: Write signal, effective at low levelRD: Read signal, effective at low levelRESET: restart signal, effective at low levelDB0-DB15: Data Cable
For example, all these cables are controlled by common I/O Ports. According to the LCD
S5pc110 LCD Driver Analysis (1) ()
// Set the register 0xf800_0130 (Video interrupt control 0 register) [16: 15] bits to 01 = vsync, which may be 00 = back porch, 10 = activeInt s3cfb_set_vsync_interrupt (struct s3cfb_global * Ctrl, int enable)// Set the register 0xf800_0130 enable or disable to [12] and [0], respectively, indicating// Intfrmen [12] specifies the video frame interrupt enable control bit.// 0 = disables video frame interrupt//
I. Purpose
Familiar with barebox frame buffer framework, LCD Driver porting and test command writing.
Ii. Main Content
Port the tiny6410-based LCD driver to the barebox in 1.1.
1.2 compile an LCD command to test the LCD driver.
1.3 write the RZ command so that you can download files to the memory through the serial po
1. Avoid unnecessary vibrations
LCD can be regarded as the most sensitive electrical equipment, LCD contains a lot of glass and sensitive electrical components, so that the screen is very fragile, to avoid strong shock and vibration, strong impact on the LCD screen and CFL unit is very easy to damage. Be careful not to exert pressure on the
The first taboo: moisture invasion
Water can be said to be the first natural enemy of liquid crystal. The destructive power of water to the LCD screen is astonishing. So you should put the LCD in a more dry environment to use, do not let moisture into the LCD inside. For some users with a more humid working environment, you can buy some desiccant to keep the air
Author:Liu Peng
Date:2008-12-27
This paper analyzes the main data structure of the frame buffer device driver, and introduces the LCD driver.ProgramDevelopment. Basic Principles
Through framebuffer, the application uses MMAP to map the video memory to the virtual address space of the application. The data to be displayed can be displayed on the screen after being written to the memory space;
The driver allocates system memory as the memo
Here, we use the icool2416 Development Board u-boot version 1.3.4 of Guangzhou SDO.
LCD driver and serial synchronous output are added at the same time.
Modify as follows:
Add the following file gzsd2416-lcd.c under the drivers/video directory (with u-boot source code as the Directory), gzsd2416-lcd.h and s3cfb-reg.h content as follows:
Gzsd2416-lcd.c, LCD initialization and backlight control
/* * Gzsd2416
In the Linux based video surveillance acquisition system, the camera captured a frame of video image data are generally hardware automatically compressed into the JPEG format, and then saved to the camera device buffer. If you want to display the collected JPEG format on the local LCD screen, Since our Linux system does not transplant any GUI systems, consider the following: 1. Unzip JPEG format to bitmap format, i.e. JPEG decoding. 2. The decoded bit
To solve the problem of LCD Font hollow, the first thing is to check whether the resolution of the LCD is correctly set. The LCD will have an optimal resolution, like a 19-inch widescreen LCD is 1440*900 (partly 1680*1050), and a 22-inch widescreen LCD is 1680*1050, and font
Like 6 s models, iPhone 7 and iPhone 7 Plus have different screen sizes and cameras. Let's first take a look at the parameter comparison between the two mobile phones. Differences between iPhone 7 and iPhone 7 Plus Comparison model
ThinkPad-how to maintain and clean the LCD screen and precautions
Applicable models:
All laptops
Document Content:
Symptom:
There are scratches or scratches on the LCD screen.
This trace is caused by a backlog of external force on the screen shell, which makes the trackpoint mouse or keyboard buttons touch the LCD screen.
Configuration:
ThinkPad laptop
Solution:
Fundamentals of 1 system 12,864 point formation liquid crystal display12,864-point array graphic liquid crystal display application, one through C51 programming realizes to the LCD12864 LCD screen control, the liquid crystal display (LCD) has the low operating voltage, the micro power consumption, the display is flexible, the low cost characteristic. The data in the digital circuit is saved in 0 and 1, and
set, and red, green, blue, and transparency are 8 bits respectively. Or ARGB8888 is similar, just note the order and offset when you set the data structure. In the frame buffer device, the operation of the screen display point is done by reading and writing display buffer, in different color mode, the display buffer and the display point on the screen have different correspondence, showing a pixel point 8-bit and 16-bit case of the display buffer and display point of the corresponding relations
The 12,864-point array liquid crystal display module (LCM) is an array of 128-column *64 rows consisting of a 128*64 LCD display point. Each display point corresponds to a binary number, 1 for light, and 0 for off. The RAM that stores these lattice information is called the Display data memory. To display a graphic or Chinese character is to write the corresponding lattice information to the appropriate storage unit. The lattice information of a graph
Xu: http://blog.csdn.net/hduxyc/article/details/6426463
FSMC stands for static memory controller ".
After the FSMC controller is used, the fsmc_a [25:0] provided by FSMC can be used as the address line, and the fsmc_d [] provided by FSMC can be used as the data bus.
(1) When the storage data is set to 8 bits, (fsmc_nandinitstructure.fsmc_memorydatawidth = fsmc_memorydatawidth_8b)
The address corresponds to fsmc_a [], and the data bit corresponds to fsmc_d []
(2) When the storage dat
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.