A device that analyzes traffic has been deployed in the previous period and needs to mirror the port's traffic to a single copy of the server's NIC.Because the Juniper Operation command is unfamiliar, the online command is also relatively few. So write a blog record.EXthe port mirroring of the switch allows the port to
) #interfaceethernet1/e1
Console (config-if) #portmonitor1/e8
Console#showportsmonitor
Sourceportdestinationporttypestatus
---------------------------------------
1/e11/e8rx,txactive
Let's look at how the specific types of switches are configured for Port mirroring:
Port mirroring configuration method for
, select the application region of the policy (unrust to DMZ), and select Add;
650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M01/49/14/wKioL1QOfs6xqjpbAASjmYId88I119.jpg "Title =" jnat10.png "alt =" wkiol1qofs6xqjpbaasjmyid88i119.jpg "/>
Enter the Policy Name (which does not affect the configuration );
Select policy action (permit allowed, deny blocked, reject );
Select the application region, which is generally untrust to DNZ.
Select which external addresses are affected by the pol
Firewalls are often deployed on the edge of our network environment to isolate the network and protect the security of the Intranet and Internet. For example, in the edge network, MIP a public IP address to a VPN device on the Intranet, for the sake of security, EDGE networks need to have selective open ports or Protocols. MIP is as follows: 650) this. width = 650; "border =" 0 "alt =" "src =" http://www.bkjia.com/uploads/allimg/131227/0FP912P-0.jpg "/>
If IKE must be enabled during ipsec vpn,
Mirror Port simply, the flow of one (several) port (source port) of the switch is completely copied, from another port (destination port), so that the network administrator from the destination port through the analysis of the sou
A lot of friends are asking Huawei about the image of the switch. Through my existing data and documents, the various models of the switch mirroring methods are summarized. So that friends can easily check! Before the configuration, the basic concept of port mirroring is still a certain understanding!
First, the concept of po
1 Catalyst 2550/3550 support for 2 group monitor sessions
Switch (config) #monitor session 1 Destination Interface F0/4 (1 is the session Id,id range for 1-2//defines port source mirroring, which is the port traffic that the administrator wants to see
Switch (config) #monitor session 1 Source Interface F0/1,F0/2,F0/3 (space, comma, space)//define
Common brand Switch Port Mirroring) Configuration
Port Mirroring ing) allows you to copy all traffic from a specific Port to an Image Port.
> If your vswitch provides a port image, you
Mirror Port configurationMost switches support mirroring technology, which allows for easy troubleshooting of the switch. We call it "mirroring" or "Spanning". Mirroring is the copying of traffic from one port on the switch to the other (mirror
Configuration ideas1. Configure the ETHERNET0/0/20 interface as an observation port (monitoring port ) 2. Configure the ETHERNET0/0/1----ETHERNET0/0/10 interface as a mirrored portConfiguration steps1. Configure the observation portSystem-view[Switch] Observe-port 1 Interface gigabitethernet 0/0/20Command format:Observe-port
address as 1.1.1.1/32 to all destination addresses[SwitchA-acl-adv-101] Rule 0 permit IP source 1.1.1.1 0 destination any3. Define a rule message source address as the destination address of all source addresses 1.1.1.1/32[SwitchA-acl-adv-101] Rule 1 permit IP source any destination 1.1.1.1 04. mirror the packets that comply with the preceding ACL rules to the E0/8 Port[Switcha] mirrored-to ip-group 101 interface E0/82-layer stream-Based Image 〗1. De
The following content is taken from April this yearNew MarketOf《Cisco/H3C switch advanced configuration and management technical manual, Companion articles --Cisco/H3C Switch configuration and management manual version 2nd)It is also selling well nationwide.18.1.2 H3C Switch Port Mirroring Principle
As described above, H3C Ethernet switches support local port im
S5700 Switch Configuration Port mirroringEnter system view, return user view with Ctrl + Z.[Quidway][Quidway]observe-port 1 interface gigabitethernet 0/0/1//observe: Observe that the listener is named 1 with the 1 port of the switch full meaning: The 1 port of the switch as the listening
Before the clutch, H3C different types of equipment command is not the same, just a simple check, from S3100 above, including S36, S55, S75, are the following configuration to grab the package (is to configure a local group, and then configure monitor port and Mirror Port):# Create a local mirror group. [Sysname] mirroring-group 1 local # Configure the source
A port image is a method of mirroring data from one or more ports of a vswitch to one or more ports, it copies packets of the specified port and VLAN to other ports. The destination port is connected to the data monitoring device, to analyze the traffic of one or more network interfaces, you can configure a vswitch to
Port mirroring, which forwards data traffic from one or more ports to a specified port via a switch or router for traffic monitoring analysis.The function of mirroring is simply to mirror the monitored traffic to the monitoring port so that the monitored traffic can be fault
In order to manage a network, the network grasping the packet Analyzer is essential, but now is no longer the hub era, grab bag is not so easy, but there is always a way to mirror the port, the other port data copy to the port you specify, so you can grab the bag. Today is not about grabbing bags, It is mainly about how to configure the Cisco switch
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.