juniper ssg 20

Want to know juniper ssg 20? we have a huge selection of juniper ssg 20 information on alibabacloud.com

The-JUNIPER-SSG series of PBR (Policy Routing) configuration finalization

/5Description E4s5700-g0/0/5-app3-eth1Port Link-type TrunkPort Trunk Allow-pass VLAN All traffic-policy PBR Inbound By the end of this configuration, the final test can be done.Here, I'll post the route trace diagram before the configuration:650) this.width=650; "src=" Http://s5.51cto.com/wyfs02/M00/8A/20/wKioL1goZrKD47sHAAB4zor-_Ys729.png "title=" Qq20161113211209.png "alt=" Wkiol1gozrkd47shaab4zor-_ys729.png "/>The following is a configured route

JUNIPER-SSG Series Sub-interface (one-arm routing) configuration termination

configurationSet interface ethernet0/1.2 NAT(PS: note Interface and area, and VLAN tag, here the 10.10.2.1/24 is sw-a Vlanif2, so here to correspond together,), click-ok output such as650) this.width=650; "src=" Http://s5.51cto.com/wyfs02/M02/7E/02/wKioL1b09h_jBsghAABG3-iUbKs283.png "title=" 4.png " alt= "Wkiol1b09h_jbsghaabg3-iubks283.png"/>Please note that once the sub-interface is established, the default is up, the number behind the interface is Vlan-tag (i.e., the downstream switch trunk c

Juniper SSG 550m HA Configuration

will see the image information below, and the HA notice light color indicates that HA is working properly.When the device is operating normally, both devices ha status lights are flashing green, but Ha is standby haThe indicator light is shown as orange * * * *.If the port of one device is down, the device automatically switches to a different host and the switch time is1 seconds, and this interface works as down the device HA indicator is shown in red.Because only port monitoring is involved i

Juniper-ha SSG Series Cluster-id solutions to scarcity problems

Juniper-ha SSG Series Cluster-id solutions to scarcity problems.Http://forums.juniper.net/t5/ScreenOS-Firewalls-NOT-SRX/Cluster-ID-issue-on-ssg140/m-p/15312//true(Answer from Juniper's official technician)By default, NSRP would support up to 8 cluster ID ' s and 8 VSD ' s. As noted in the previous entry, you can increase this with the Envar, but you need to use them in multiples of 8, and the combination of

Juniper-ssg-netscreen series High Availability CLI configuration finalization

Group id:0L Device priority in the VSD group:100L Preempt option:disableL Preempt Hold-Down time:0 SecondL Initial State Hold-Down Time:5 SecondL Heartbeat interval:1000 millisecondsL Lost Heartbeat Threshold:3L Master (Primary) always Exist:noRTO Image InformationL RTO synchronization:disableL Heartbeat Interval:4 SecondL Lost Heartbeat threshold:16NSRP Link InformationL Number of gratuitous arps:4L NSRP encryption:disableL NSRP authentication:disableL Track Ip:noneL Interfaces Monitored:noneL

JUNIPER-SSG Series Sub-interface (single-arm routing) application

of multiple gateways)V. Review of implementationSingle-arm routing long application in small and medium-sized enterprises, when the enterprise can not budget to buy three-tier switch, through the two-layer switch to achieve multi-VLAN interoperability.The implementation of the cross-border delivery, because the customer needs inter-VLAN interoperability, I have not done here strategy, the following is a simple introduction of the SSG series of strate

Juniper SSG Common Commands

NetScreen Juniper SSG Operation commandApril 10, 2013Command line get configuration information get configcommand line to get the time set to get clockSet Vrouter TRUST-VR sharable settings Consider router TRUST-VR can share set Vsys "Vrouter"/Set virtual router for other UNTRUST-VR systems Set Vrouter "TRUST-VR"/Set Virtual router set zone "Untrust" Vroute "UNTRUST-VR" zone untrust to U In NTUST-VRZone Unt

Mutual access between different network segments of Juniper SSG Firewall

Problem description: When the SSG series firewalls of Juniper can access each other through VPN dial-in or direct mutual access between different network segments, sometimes PING can be reached, but the service cannot be accessed, such as WEB and shared files. Problem Analysis: These problems are often caused by the identification of data packet fragments by devices during data transmission.

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.