juniper vlan configuration

behaviorSet Firewall family ethernet-switching filter acl_name term rule_name1 then discardIt is important to release other traffic, because the resulting ACL will automatically have a rule of any discard.Set Firewall family ethernet-switching filter acl_name term rule_name1 then acceptPut it on the VLAN that has the correspondingSet VLANs vlan_name Filter input acl_name---------------------------------------------------------------------------------

[Juniper] common configuration methods for daily maintenance of switches and routine maintenance of juniper The juniper device is different from other vendors, and adopts the configuration concept of submitting for effectiveness. This greatly reduces misoperations. Note: Al

port) is not connected to the network cable. You can manually close the ALARM of the Management port and use this command in juniper: # Set chassis alarm management-ethernet link-down ignore # Commit The light gradually becomes orange. Add another command # Set chassis alarm ethernet link-down ignore # No alert is generated when you set all ports (Note: link-down can detect the port status. If you have set an alarm for Port link down, it is best to d

Enable disabling of a port[Email protected]# set Interfaces GE-0/0/4 disable #1. Close port[Email protected]# Delete interfaces GE-0/0/4 disable #2. Recovery portConfigure MGT Port IP[Email protected]# set interfaces ME0 Unit 0 family inet address 192.168.1.1/24Setting interface Parameters[Email protected]# Edit Interfaces GE-0/0/1[Email protected]# set description "Connect to Juniper 6350" # "Set Port description"[Email protected]# set mac 00:1f:12:3

public VLAN must correspond one to one, that is, each private VLAN can only be mapped to one public VLAN, at the same time, each public VLAN can only be mapped by one private VLAN. L if you want to modify an existing VLAN Mapping

Experiment on a PC running FreeBSD and Junos, topology as above: Virtual IP (VIP) addresses = 10.0.5.253 and 10.0.6.253 R1 is Master's VLAN 520 and R2 is back R2 is Master's VLAN 530 and R1 is back MD5 authentication is enabled. For VLAN 520, the key is ' vrrp520 '. For VLAN 530, the key is "vrrp530" My virtual ro

The diagram above is a configuration topology diagram R1,R2,R3,R4 all RIPv2 get the route, the following is the configuration document. System {root-authentication {Encrypted-password "$1$pc0igedw$xh19u99vsa6azotdk9bfz."; # Secret-data} logi n {User Mengmeng {UID 2001; Class Super-user; Authentication {Encrypted-password "$1$keim0kf/$ezlHwRupnb 7HFdUZVdIvE."; # # Secret-data}}} Services {telnet;

Experimental topology650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/6F/7D/wKiom1Wd7-Pw1yLkAAFCmeJywRY388.jpg "title="}~ 4SQ4DEE8$8ZEM~F3 (8bh4.png "alt=" Wkiom1wd7-pw1ylkaafcmejywry388.jpg "/>C1 ip:192.168.10.1/24 C5 ip:192.168.10.5/24C2 ip:192.168.10.2/24 C6 ip:192.168.10.6/24C3 ip:192.168.10.3/24 C7 ip:192.168.10.7/24C4 ip:192.168.10.4/24Experimental requirements1, C1 and C2 belong to VLAN10,C3 and C4 belong to Vlan20,c5 and C6 belong to VLAN30,C7 belong to Vlan402, members of the

Configuration of Virtual LAN (VLAN), lan vlan Figure 1 Experiment Topology Lab content: (1) Name the switches SWA and SWB respectively. (2) divide Virtual LAN VLANs and statically divide ports into valn. First, use two methods to divide VLANs. L vlan division in global mode: This method is used to create three VLANs

I. Demand1, divide three VLAN VLAN2 Server 1-8 Port Network VLAN3 work01 9-16-Port Vlan4 work02 17-24-Port 2. Gateway Configuration 192.168.2.1/24 192.168.3.1/24 192.168.4.1/24 3, DHCP and reservation Each section to open DHCP, each reserved xx.2-xx.10 segment IP for reserved use 192.168.2.10/24 for AD domain server, concurrently as a DNS server, plus two additional alternate DNS 114.114.114.114 8.

configurationSet interface ethernet0/1.2 NAT(PS: note Interface and area, and VLAN tag, here the 10.10.2.1/24 is sw-a Vlanif2, so here to correspond together,), click-ok output such as650) this.width=650; "src=" Http://s5.51cto.com/wyfs02/M02/7E/02/wKioL1b09h_jBsghAABG3-iUbKs283.png "title=" 4.png " alt= "Wkiol1b09h_jbsghaabg3-iubks283.png"/>Please note that once the sub-interface is established, the default is up, the number behind the interface is

routing pattern application:① registered IP (public network IP address) the number of more;② the number of non-registered IP addresses (private network IP addresses) is equal to the number of registered IP addresses (public IP addresses);The ③ firewall deploys the application completely in the network.2.3. Transparent modeWhen the Juniper firewall interface is in "Transparent" mode, the firewall will filter through the IP packets, but will not modify

/5Description E4s5700-g0/0/5-app3-eth1Port Link-type TrunkPort Trunk Allow-pass VLAN All traffic-policy PBR Inbound By the end of this configuration, the final test can be done.Here, I'll post the route trace diagram before the configuration:650) this.width=650; "src=" Http://s5.51cto.com/wyfs02/M00/8A/20/wKioL1goZrKD47sHAAB4zor-_Ys729.png "title=" Qq2016111321

In order to prevent the Juniper Firewall equipment failure in the case of network interruption, to ensure the uninterrupted operation of the user business, the Juniper Firewall is the case of the rapid recovery of the specific description. Juniper Firewall configuration Backup, device restart:

To prevent network interruptions caused by the failure of the Juniper firewall device and ensure uninterrupted operation of user services, we will describe the rapid recovery of the Juniper firewall under the fault.One of the backup configurations of the Juniper firewall and the restart of the device: if the system reset is required when the

As shown in the topology map, AREA2 and area0 are not directly connected, so the network does not have a full topology, at which point we can do virtual-link on the ABR area2 and AREA0 connection, the following is the configuration script: system {Time-zone Asia/shanghai; root-authentication {Encrypted-password "$1$eb9tnuwo$gyal5nxlo7vdl4n6mrndy1"; # Secret-data} l Ogin {User Olive {UID 1000; Class Super-user;

First of all, for the theory of literacy, you need to understand ha what it is and whether it is similar to other high availability, not much to say. You can look down.Juniper-netscreen os ha High availability configuration HA NetScreen Company's NSRP agreement is Juniper company based on the VRRP protocol specification independent Development Agreement, the firewall as the core network of the

Lab Environment:Routers make Tp-link set up NAT forwarding, Tp-link router gateway is set to 192.168.30.254 ( core layer) Cisco 35,503 layer switch (model C3550-I5Q3L2-M) configuration three Vlan,vlan 10, VLAN 20, and VLAN 30IP address for

An instance of VLAN configuration for Cisco L3 switches and L2 SwitchesCisco VLAN implementation is usually port-centric. The port connected to the node determines the VLAN in which it resides. There are two ways to allocate a port to a VLAN: Static and Dynamic. The process

In the front I sent an article "Juniper Firewall diagram L2TP VPN Configuration", we learned from that article how to configure. But we know that the L2TP VPN is only connected to our L2TP VPN server, but it doesn't encrypt our data, and we know that IPSec's data is encrypted, and if the IPSec-unaware friend can look at my previous IPSec VPN concepts (i) And the concept of IPSec VPN (ii) to understand. Okay