juniper vlan configuration

VLAN partitioning based on MAC addresses is divided into three types:First type: Manually configure the static Mac VLANSecond type: Dynamic trigger port joins static Mac VLANThird type: Dynamic Mac VLANThis document describes the manual configuration of the first static Mac VLAN; Environment: H3C ENSPFirst step: Build Vlan:vlan 100Step two: (

Experiment: Huawei mux vlan configuration and management The following experiment is an experimental video teaching course designed by the author for "Huawei switch Learning Guide". Click here to view details: http://edu.51cto.com/course/course_id-2091.html The mux vlan function of Huawei enables layer-2 communication between different VLANs located in the same I

VLAN configuration for linux Nic in virtual deployment (1) This article from Bkjia "Drop water stone Sun Jie" blog, original address: http://xjsunjie.blog.51cto.com/999372/1633815 If the switch port connected to the server has been configured with TRUNK in advance and allows specific VLANs to pass through, the server Nic must be configured with the corresponding

Role of the switch serial port (Trunk: The following two encapsulation types can be used for relay over Ethernet through the serial port of the switch: -IEEE 802.1Q -ISL (Inter Switch Link, Cisco private) Procedure Step 1: Add a VLAN to the vswitch Switch1 # vlan database Switch1 (vlan) # vlan 2 Switch1 (

Two vswitch configuration modes: Configure VLAN Based on port division as an example. Vswitch configuration modes can be divided into two categories: one is the configuration mode represented by a CISCO switch, and the other is the configuration mode represented by a Huawei

network router end, you need to configure the server end. Here, we mainly set IP addresses and routes. Note that if the port is tagged, the server's IP address must be configured with the corresponding vlan id. Here, we use the solaris server as an example. On solaris 10, the network port configuration is as follows: root @ solaris :~ # Ls-lah/etc/hostname. *-rw-r -- 1 root 13 2011-07-20 05:21/etc/hostname

Experiment topology:Objective: To: (1) Disable pc3 access without affecting hosts on other LAN(2) enable all hosts in the LAN to access the Internet. (Only one public address is available)(3) automatically obtain the Host IP address in the LAN.(4) r1 provides single-arm routing and dhcp functions to implement inter-vlan CommunicationIn accordance with the above requirements, to allow all hosts to access the Internet with only one public IP address, yo

Recently, a number of Cisco ucs c Series servers have been added. After two weeks of deployment and installation, the server can finally be tested. This document briefly introduces the network configuration of the Operating System (centos 6) in the Cisco UCS server. It can be simply considered that this article describes the network configuration of a physical server connecting the NIC to the trunk mode por

VLANThe typical configuration process is as follows: Networking Diagram Figure 1-1 port-based VLAN networking Application Requirements As shown in Figure 1-1, Switch A and Switch B connect Host1/Host2 and Server1/Server2 used by different departments. To ensure data isolation between departments, you must divide Host1 and Server1 into VLAN100 and Host2 into VLAN200. Set the description characters for the t

Experimental topology650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/6F/93/wKiom1Wgz6yQRSAIAAEE1Z-_Pis893.jpg "title=" p028wn (19qdj$3egpk0ltv3.png "alt=" Wkiom1wgz6yqrsaiaaee1z-_pis893.jpg "/>Experimental requirements1, C1 and C3 belong to VLAN10,C2 and C4 belong to VLAN20, on SW1 to create VLAN100 do upstream VLAN2. End all VLANs on SW13. Use DHCP to get IP on all VLAN members4, the whole network interoperabilityIP planningVlan10:192.168.

option is to submit only the specified name list (you can use show Security acl ip name editbuffer to view control entries not submitted to the content in the editing buffer ), the all option is used to submit all unwritten vacls.3. Map to VLANBoth vacl and ACL must be mapped to the target object after submission, for example, interface vlan1 // ip access-group 101 out: apply access-list 101 to the out direction of the vlan1 interface. 101 indicates the ACL number and is associated with the cor

2618 switch VLAN configuration Switch A and switch B are connected through port 16. Port 1 of Switch A and Port 2 of Switch B are members of VLAN2, port 2 of vswitch A and port 4 of vswitch B are members of vlan3. 1.15 configuration steps vswitch A is configured as follows: zte (cfg) # set vlan 2 add port 16 tag // add

H3C S3100 Switch configuration VLAN I. Basic settings 1. the console line is successfully connected. 2. Enter System Mode 3. Change the device name [H3C] sysname TEST 4. view all configuration information [H3C] display current-configuration // display this is to view the device information in the curren

Tag: mode command using log ENC Global relay name configurationSwitch interface type: Access: Access mode, PC via switch internet this way Trunk: Trunk mode, inter-switch connection in this way Switch VLAN creation mode: Database configuration mode Global configuration Mode Database configu