kanban board system

NFS file system of Linux virtual machine on the Development Board Http://apps.hi.baidu.com/share/detail/48189956 Today, I did an experiment on embedded applications. How can I run cross-compiled applications on your host on an embedded system? Here I chose to mount the NFS file system over a network. My lab environment

Design of serial communication system between FPGA and GPS-OEM Board [Date:] Source: Electronic Components application Author: Chen shilei, Liu Guixi, to Guohua [Font:Large Medium Small] 　 0 Introduction Global Positioning System (GPS) is the second generation of satellite navigation system in the

This article goes from Schindler to Forum: http://topeetboard.comDevelopment platform: iTOP-4418 Development BoardSystem: Ubuntu1. TF card reading and writing speed testWrite Ubuntu for the TF card requirements are relatively high, many old cards can not be burned to write Ubuntu, the following provides aA relatively reliable TF card to test the method. Note: The TF card test here is only for Ubuntu burning, burning the other file system, the general

How to run the system on the Development Board.4.0 acquisition of the Cross compiler. Manufacturers to provide online download (manufacturer confirmation)4.1 Uboot to operate.1, extract the source of the factory2, enter the source code3,make Distclean completely delete the source of the target, temporary files4,make Xxx_config is configured for a CPU and Development Board5,make compilation6, Results generat

Elite Edition in Linux under Use WiFi , the following configuration is required:First, the user to see the CD in the CD after the"Linux"--"root_xxxxxxxx.tar.gz" File, where the "xxxxxxxx " Representative linux system version Date, Schindler provides support for linux under wifi system version is " root_20150422.tar.gz "NBSP;, That is, 2015-04-22 later versions (including 20150422) are supp

Super Terminal and start it with NAND Flash. You can also ping it) 5: based on the information provided by the friendly arm. Install NFS. Paste the information as follows: 5.1 configure the Network File System NFS service If you have fully installed Red Hat 9.0 according to the methods described above, the NFS-related software has The NFS service is installed by default. Follow these steps to create and configure the NFS service. (1) set the shared d

In the previous article http://www.cnblogs.com/linzizhang/p/4817336.html introduced the first part of the system software on the Development Board--bootloader the compilation method.Background: After the bootloader is burned into the NAND flash of the Development Board, the Development Board starts from the NAND, the h

Mars board is an evaluation board based on The Freescale Semiconductor I. mx 6 dual processor. I. mx 6 Dual Processor integrates arm cortex up to 1 GHz™-A9 kernel, 2D and 3D graphics processor, and 3D 1080 p video processor.The Mars board evaluation board has a variety of interfaces, including HDMI interface, LVDS inte

/desktop/... (need to share the directory path on the ARM9 board)Bring the exports into effect,#exportfs-A(4) Under the PC Terminal, use Telnet command to go to the ARM9 board# Telnet 192.168.123.100 (then root)(5) Mount the folder with the Mount command (in the ARM9 Board directory)#mount-T Nfs-o nolock 192.168.123.120:/home/wzy2015/desktop/yanxingmei/mnt/nfs (I

File transmission through serial ports between the embedded Linux System and the host I think if I want to download something from my PC to the embedded Linux System of the Development Board, many people will first think of using network tools such as TFTP SFTP to download it from the network port. But if the network is not used, what should I do if I can only

Objective:Recently in the use of OK6410 Development Board running Linux system, often on the terminal to knock some instructions, but the Development Board screen is too small to use it very inconvenient, so the use of a terminal can run in the software on Windows is connected to the Development Board and operates the