link aggregation router

. The current change number is one, the CHANge Loop count is 0, and the maximum number of records is 4095.[S1]int[S1]interface gi[S1]interface gigabitethernet 0/0/2[S1-gigabitethernet0/0/2]eth[S1-gigabitethernet0/0/2]eth-trunk 1Info:this operation may take a few seconds. Please wait for a moment...done.[S1-gigabitethernet0/0/2]q[S1]09:33:57-08:00 S1 ds/4/datasync_cfgchange:oid 1.3.6.1.4.1.2011.5.25.191.3.1 configurations has been changed. The current change number is, the CHANge Loop count is 0,

I. Configure the environment Centos 6.2 system. Link aggregation is performed on one and two NICs. The vswitch has six or seven Network Ports. Ii. server operation steps 1. Create a channel Bonding Interface # Vi/etc/sysconfig/network-scripts/ifcfg-bond0Add the following lines:Gateway = 192.168.10.1dns1 = 202.106.0.20device = bond0bootproto = nonenetmask = 255.255.255.0type = ethernetipaddr = 192.168.10.100

Bond configuration information[[emailprotected] ~]# cat /proc/net/bonding/bond5Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)Bonding Mode: transmit load balancingPrimary Slave: NoneCurrently Active Slave: eth1MII Status: upMII Polling Interval (ms): 100Up Delay (ms): 0Down Delay (ms): 0Slave Interface: eth1MII Status: upSpeed: 1000 MbpsDuplex: fullLink Failure Count: 0Permanent HW addr: 00:0c:29:2e:e0:a9Slave queue ID: 0Slave Interface: eth2MII Status: upSpeed: 1000 MbpsDuplex: fullLi

TP-Link wireless router settings graphic tutorial how to set a TP-Link Wireless Router DiagramThe following describes the settings of the tp link wireless router. In this example, we use a new vro. If you are not sure whether the

How to set a password for a TP-Link Wireless Router _ how to set a wireless password for a tp link RouterThe following describes how to set a wireless access password for a TP-Link wireless router. If your tp link wireless

　　Install the wireless router With the growing sophistication of wireless network technology, the price of wireless devices has also fallen to the level acceptable to our average consumer. We do not have to let the two rooms in the home computer can be at the same time the internet and a lot of trouble to pull the network with Proxy server. A wireless broadband router, a wireless network card can easily ac

How to set a password for a TP-Link Wireless Router _ how to set a wireless password for a tp-link router tutorial, tp-linktpThe following describes how to set a wireless access password for a TP-Link wireless router. If your tp

Vswitch basics: aggregation technology in IRF Architecture IRF technology combines multiple switching devices into a high-performance whole to achieve the highest possible network performance and network availability with minimal overhead. Devices supporting IRF technology have three important features: distributed device management (DDM) and Distributed Link aggregation.DLAAnd distributed elastic routing (

With the rapid development of routes, new technologies are also emerging. Aggregation routers are one of them. Compared with traditional routes, aggregation routers have many advantages, the main characteristics and advantages of the application are described here. How can we improve the performance and service quality of the Aggregation

Tutorial topology: 650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M00/47/BF/wKiom1P_THjC8klUAAFlyn6ovHE323.jpg "Title =" 1.png" alt = "wkiom1p_thjc8kluaaflyn6ovhe323.jpg"/> R3 is a gateway, R4 is an egress router, and DHCP is used. R5 is a vro on the Internet. Lab requirements: 1. Three PCs belong to three VLANs 2. R1 and R2 are used for Link aggregation