Design of starting U-BOOT from nand flash memory
Introduction
As embedded systems become increasingly complex, the demand for large-capacity data storage becomes increasingly urgent. However, hard disks cannot be widely used due to the low power consumption, small size, and low cost requirements of embedded devices. Nand fla
NAND Flash and nor
Flash is often mentioned in some places and has never understood their differences seriously. Therefore, I have spent some time understanding them carefully today. I will put my notes here below :)
1. Nor is characterized by in-chip execution (xip, execute in
Place), so that the application can run directly in
Flash has the characteristics of power-down data storage. If Ram power-down occurs, data is lost, but Ram speed is higher. Theoretically, there is no limit on the number of writes, But Flash does not.Compared with other types of flash, NAND Flash has the advantage of high er
The non-easy slipped speed memory flash has the characteristics of high speed, low cost and large density.Flash memory mainly has nor flash and NAND flash two types, in general, nor type is more suitable for storing program code, NAND type can be used for large-capacity data
video data from the specified memory space. The encoded data can be stored locally or remotely, or sent to the network using the RTP protocol.The entire process is coordinated by the ARM core. In order to improve efficiency, a large number of DMA operations and the continuous storage space allocated by the cmem module are used.
Texas Instrument Onsite technical support engineer Meng Haiyan
Summary:
This article introduces the principle of starting dm368
Original: http://xianzilu.spaces.live.com/blog/The NAND Flash Driver of smdk2410 in U-boot. I shouldn't have written this first. Oh, but I have a poor memory. Maybe I forgot where I got the code during the porting process in a few days. First, I would like to celebrate that all my exams are over, hahaha. But do not try again ...... I heard that the course of our graduate student dean Zhao xuezeng is abnorma
For many consumer audio and video products, NandFlash MemoryIt is a better storage solution than hard drive, which is particularly evident in low-capacity applications with a size not more than 4 GB. As people continue to pursue products with lower power consumption, lighter weight, and better performance,NandIt is proving very attractive.
The nand flash memory array is divided into a series of KB blocks, w
This article describes the method of using Texas Instruments xds100v2 USB emulator to burn write omap-l138 program to NAND flash and boot from NAND flash. 1 software used
(1) aisgen_d800k008;
(2) Omap-l138_flashandbootutils_2_40.tar;
(3) Omapl138-dsp-led-v4.zip;
(4) DSP project generated by the A.out file, that is to
Create a yaffs2 File System on NAND Flash (1)
ByOn2006-07-22
After more than half a month of hard work, we finally completed nandflash's MTD driver and the upper-layer yaffs2 file system. In the past half a month or so, we have to fight against frustration almost every day. Every day, we have to endure this bug. I think I have been reading a lot of materials over the past half a month. I have gained some h
[Switch] xip-execute in place, which is often translated into Chinese and executed in local mode. Indicates that the code can be executed in the current memory.
About nor flash xip:
Nand and nor and xip
"Nor features in-chip execution (xip, execute in place), so that applications can run directly in flash memory without having to read the code into system Ram. No
Nor and NAND are two major non-loss flash technologies on the market. Intel first launched nor in 1988Flash technology has completely changed the previous integration of EPROM and EEPROMThe world. Next, in 1989, Toshiba published the NAND Flash structure, emphasizing the reduction of the success rate of each bit.Higher
Why are there two ways to start?This is determined by the different characteristics of two types of flash.NAND flash capacity is large, the cost of storing the unit bit data is much lower, but to read and write to NAND flash according to the specific timing, so the CPU can not directly address the NAND
[What is onenand flash]
Onenand is a highly reliable embedded storage device designed for consumer electronics and the next-generation mobile phone market.With the development of NAND technology over the past few decades, some companies, based on the original NAND architecture,An ideal single storage chip is designed, which integrates the SRAM cache and logic int
This article is not about the physical structure of NAND flash and some basic knowledge about NAND flash. You need to know at least the physical structure of NAND flash on your hands and some such as read-write commandsThe general
Nor and NAND are two major non-loss flash technologies on the market. Intel first developed nor Flash technology in 1988, which completely changed the previous situation where EPROM and EEPROM were integrated. Next, in 1989, Toshiba published the NAND Flash structure, emphas
Introduction to basic concepts of NAND FLash and basic concepts of nandflash
I. Pin Introduction
Pin name
Pin Function
CLE
Command lock function
ALE
Address lock function
/CE
Chip enabling
/RE
Read enabling
/WE
Write enable
/WP
Write Protection
R/B
Ready/busy output signal
Vcc
Power Suppl
First, the characteristics of NAND flashThe s3c6410 NAND Flash controller has the following features1, since the import mode: After the reset, the boot code is fed into the 8KB steppingstone, the boot code is moved, the boot code will be executed in Steppingstone. During import, the NAND
Tags: blog HTTP Io ar use for SP file data
First, let's clarify our programming steps.
(1) power up the program within 4 K of boot. s in nand_flash. This 4 K will be automatically copied to the SRAM (in-chip RAM) for execution.
(2) We need to use this 4 K program to copy the program after 4 K in NAND Flash (of course, copy the program to the base address of SDRAM at 0x30000000) and continue the execution (m
Mpc8313erdb Code Analysis of Uboot environment variables read from NAND flash in Linux[Email protected]One. Story causeBecause the file system has grown, it has greatly exceeded the 8MB nor FLASH, and has had to save the kernel, file system and device tree files to NAND flash
Analysis of NAND Flash Driver in Embedded Linux
I. Description of the source code file of the NAND Flash Driver
In the Linux kernel, The MTD source code is stored in the/driver/MTD Directory, which contains six subdirectories: chips, devices, maps, Nand, onenand, and ubi. On
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.