Many people may not have a special understanding of setting policy routes. So I have studied VLAN-Based Configuration Policy routes. Here I will share with you, hoping to help you. With the popularization of networks, how can small-sized enterprise local networks spend less money to implement more complex network functions in the case of a shortage of funds to meet people's needs for higher network functions, it is a concern of network technicians.
In
from a group of MAC addresses. GMRP transmits such group information between vswitches on the Internet, so that vswitches can update their filtering information to implement extended service functions. A vswitch has the filtering service and extended filtering service without any configuration. Because the old vswitches, hubs, and routers do not support dynamic multicast address filtering, the corresponding ports connected to them need to be configured with extended filtering. The switch filter
Tags: ref text S/4 share picture TE forwarding csdn vlan equalAcess PortTicker: Determine if there is VLAN information: if there is no pvid on the upper port, and exchange forwarding, if there is a direct discard (default)Text: The VLAN information of the message is stripped, sent directly outTrunk PortTicker: Determine if there is
In this section we look at how to implement and configure the following VLAN networks in an experimental environmentConfigure VLANsEdit/etc/network/interfaces, configure eth0.10, Brvlan10, eth0.20, and Brvlan20.The following shows the modification of/etc/network/interfaces with Vmdiff.Restart host, ifconfig each network interfaceUse Brctl Show to view the configuration of the current Linux Bridge. Eth0.10 and eth0.20 were hung on brvlan10 and Brvlan20
Voice VLAN concept and networking concept: the so-called voice vlan uses vlan to identify a packet as a Voice packet, and the packet carries voice data. In networks where voice messages and data packets coexist, vlan-based voice packets are identified to distinguish voice messages and data packets, and a higher priorit
Switch Port vlan mode Ø the Acess port receives a packet to determine whether there is any VLAN information: If there is no vlan information, the PVID of the port is entered and the switch is forwarded. If yes, the packets are discarded directly (default) Ø send packets on the Acess port: the VLAN information of the pa
Inter-VLAN RoutingMulti-layer switch between VLANs ip Address: 1. for local or end-to-end VLANs, the recommended number of hosts in a single vlan is 100-200.2. for layer-3 point-to-point interfaces, we recommend that you use a 30-bit mask when designing the p level. Devices that implement vlan routing: 1. any layer-3 Switch 2. any external router with interfaces
Three-layer switching technology: two-layer switching technology + three-layer forwarding technology. It solves the network segment in the LAN, the network segment must rely on the router to manage the situation, to solve the traditional router low speed, complexity caused by the bottleneck problem.650) this.width=650; "Src=" Http://s1.51cto.com/wyfs02/M01/84/63/wKioL1ePKkTAgqs8AACyLCFWuCA902.png-wh_500x0-wm_3 -wmp_4-s_366222421.png "title=" three-layer switching
, and completely using ASIC hardware to achieve routing and switching at line speed, the latter represents the fast ip of 3com, and the virtual fast Security Network of cabletron. The method used is to route the network at the first layer, then, the second layer switches the end-to-end network stream data group. This is the policy of "one route, then switch.
The powerful functions of the layer-3 Exchange router are as follows:
(1) routes are calculated based on the L3 protocol. The supported ro
In the two-layer network, when transmitting two beginning, it needs to be forwarded with the outer VLAN of the message, while the outer tag of the user network is usually inconsistent with the VLAN of the carrier network, so the VLAN stacking and VLAN mapping and dot1q tunnel etc. Unlike
Huawei vlan division, single-arm routing and Static RoutingHuawei vlan division, single-arm routing, and Static Routing allow all members to access the InternetHuawei topology: IP address planning! Assign IP addresses to three computersVLAN Division:[Huawei] un in en close message center[Huawei] Change the switch name in sysname SW1[SW1] inter vlan 1 enters the s
We know that the traditional LAN Ethernet adopts the CSMA/CD method with conflict detection. In the CSMA/CD network, nodes can use the network whenever they have data to be sent. Before a node transmits data, it performs a "listener" to check whether the network is busy. If not, the node starts to transmit data. If the network is in use, the node waits. If the two nodes do not hear anything and start to use the line at the same time, a conflict will occur. When sending data, if it uses a broadca
We all know that DHCP is a service for IP address management. In some network changes, we also need to modify the settings. Here we will explain how to configure the multi-vlan dhcp service. All aspects must be taken into account when upgrading the network, and how to implement the DHCP service in a multi-VLAN environment is one of them.
Multi-vlan dhcp service s
As we all know, the vswitch ports are both layer-2 interfaces, and these interfaces are connected to physical ports. In a Vlan, these interfaces can be divided into access interfaces and relay ports. If the port of a vswitch uses an access port, it can only belong to a specific Vlan. If the port of a vswitch uses a relay port, it can belong to any Vlan. So when s
I have been learning cisco devices for a while and have never used them in the work environment. I am using a silly switch and adding an FW to the Internet. Considering that the unit is a domain environment, A three-tier switch will be added to the data center next year, and a two-tier switch will be added to the factory. Therefore, a virtual machine will be used to complete VLAN-based experiments in a single-domain environment. This will lay a founda
What is a VLAN: one VLAN is across multiple physical LANs Network Segmentthe logicBroadcast Domain, people design VLANs to Workstationsprovides separate broadcast domains that are logically segmented based on their capabilities, project groups, or applications regardless of their user's physical location. avlan=a broadcast domain=Logical Network SegmentVLANThe advantages and installation features:VLANThe ad
To configure the schema:Configuration command:Switch>enableSwitch#vlan Database% Warning:it are recommended to configure VLANs from config mode,As VLAN database mode is being deprecated. Please consult userdocumentation for configuring Vtp/vlan in config mode.Switch (VLAN) #vlan
Hands-on practice of Linux VLAN-playing with OpenStack (13) every five minutes)
This section describes how to implement and configure the following VLAN network in the experiment environment. Configure VLAN
Edit/etc/network/interfaces and configure eth0.10, brvlan10, eth0.20, and brvlan20.Vmdiff is used to demonstrate modifications to/etc/network/interfaces.
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.