nest humidity sensor

Physical map650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M02/8B/2F/wKioL1hGsMORxBttAAJMGUmukvs286.png "title=" Am2320.png "alt=" Wkiol1hgsmorxbttaajmgumukvs286.png "/>Pin diagram650) this.width=650; "src=" http://s5.51cto.com/wyfs02/M00/8B/33/wKiom1hGsM-Db6GDAADX2K1req8130.png "title=" pin. png "alt=" Wkiom1hgsm-db6gdaadx2k1req8130.png "/>Wiring diagram650) this.width=650; "src=" http://s2.51cto.com/wyfs02/M01/8B/33/wKiom1hGsN7i8SMAAAGFqcnBRuE198.jpg "title=" Img_ 20161206_203345.jpg "

Source: http://www.ieechina.com/Upload/Tech/748.htmAbstract:　 The integrated humidity sensor ih3605 can adjust the signal in the chip, and has high precision and good linearity. This article introduces its performance and structure features, and provides typical application instances of ih3605.Keywords:Humidity Sensor; integrated circuit; ih3605Document Identific

Recently used in the temperature and humidity sensor, AM2305 drive, single bus, on the power of at least 2S to read temperature and humidity, temperature accuracy is high, like DS18B20, data with the checksum, will not appear ds18b20, and the timing is not high /****************************************************************************************************

If you want to use the Arduino Development Board drive DHT11 to obtain temperature and humidity, it is recommended to use a third-party library, which can speed up the development of the program, and is not prone to error, the following code I have been transferred to the third-party library. For detailed installation methods, please refer to the Geek Pioneer's blog: The http://www.cnblogs.com/jikexianfeng/p/6290203.html author installs the minimum ve

) = = GPIO. Low: Continue While gpio.input (channel) = = GPIO. High: K + = 1 if k > : Break If K 8: Data.append (0) Else: Data.append (1) J + = 1 Print "sensor is working." Print Data #输出初始数据高低电平 Humidity_bit = data[0:8] #分组 Humidity_point_bit = data[8: +] Temperature_bit = data[: Temperature_point_bit = data[: +] Check_bit = data[:

AM2321 is a digital temperature and humidity sensor in Guangzhou ausone electronics production. Although it is a domestic brand, its precision can be comparable with foreign mainstream temperature and humidity sensing IC. Size: 11.3x7.8x4mm (L x W x H) Package: 0.05 pitch PTH Operating voltage: 2.6~5v Interface: i²c, maximum rate 100kbps, wit

SI7021 is a temperature and humidity sensor chip produced by Silicon Labs. Its main features: Humidity accuracy: Error typ. +/-2%RH, Max +/-3%rh (0~80%RH), factory corrected Temperature accuracy: Error typ. +/-0.3%°c, Max +/-0.4%°c ( -10°c~85°c), factory corrected Measuring range: Temperature range 0~100%rh, maximum temperature range -40°c~125°c

functionNvic_prioritygroupconfig (nvic_prioritygroup_2);//set interrupt Priority group to group 2:2-bit preemption priority, 2-bit response priorityUart_init (115200);//serial port initialized to 115200Led_init ();//initializing the hardware interface to the LED connection while(Dht11_init ())//DHT11 Initialization{printf ("DHT11 error\r\n"); Delay_ms ( the); } while(1) { if(t% -==0)//Read once per 100ms{dht11_read_

Recently used temperature and humidity sensor, AM2305 drive, single bus, after power on at least a delay of 2S to read temperature and humidity, temperature accuracy is high, with the same as DS18B20, data with calibration, will not appear ds18b20, and timing requirements are not high /****************************************************************************

The previous period of development of telemedicine system (Dr.cloud) has used over temperature and humidity sensor, but at that time considering the difficulty of integration, selected a RS485 interface sensor, the sensor realizes the Modbus RTU slave function, as long as the client program to achieve Modbus RTU The cl

http://blog.csdn.net/qwert1213131/article/details/35828873 This article belongs to the individual understanding, the ability is limited, the mistake is unavoidable, also looks correct. "Little Fish has a little electricity." "Espruino Chinese Community" In section 10th, a DS18B20 temperature sensor is introduced, which introduces a sensor DHT11 that detects temperature and

] |=1;//writes data 1 toJ + +;}}/*Start processing data 1. Because a complete data output is 40 bits, J should be greater than 402.dht11_val[4] for checksum, here to determine if the checksum is correct 3. Print only dht11_val[0], dht11_val[2] because dht11_val[ 1], dht11_val[3] is a fractional part, according to the data sheet decimal is always zero*/if(J >= +) (dht11_val[4] = = ((dht11_val[0] + dht11_val[1] + dht11_val[2] + dht11_val[3]) 0xFF)) {printf ("rh:%d,temp:%d\n", dht11_val[0], dht11_

Boot Root Automatic LoginIf you want to enter in the HyperTerminal, login and execute, you can add commands in the/etc/profile;If you implement an automatic login for power on, and modify it in/etc/inittab, each development board may be modified in a different way.Http://blog.chinaunix.net/uid-27717694-id-3543938.htmlAuto-run application on bootBypass login, only need to directly modify/etc/init.d/rcs a file, add a program or script command can be run automatically:Similar to Autobat automatic b