network with two routers

Cisco speed limit Steps1. Set ACLAccess-list 102 Permit IP host 192.168.10.2 anyAccess-list 102 Permit IP any host 192.168.10.2Access-list 103 Permit IP host 192.168.10.3 anyAccess-list 103 Permit ip any host 192.168.10.32. Defining classesClass-map Match-all 102Match Access-group 102Class-map Match-all 103Match Access-group 1033. Adding classes to the policyPolicy-map XiansuClass 102Police 1024000 128000 conform-action transmit exceed-action dropClass 103Police 1024000 128000 conform-action tra

(config ) #router NBSP;RIPNBSP;NBSP;NBSP;NBSP;NBSP;NBSP;NBsp;//Entering routing configuration mode - Enable RIP protocol router (config-router) #version 2 //using version 2, RIPV2 protocol router (config-router) #network 192.168.1.0 NBSP;//Specifies the network that needs to be advertised (located in the routing interface) Router (config-router) #network 222.200.105.0router (config-router) #exit/*=part3 static NAT configuration */router (config) #inter f0/0router (config-if) #ip natinside //Se

peer-to-peer physical port should support the trunk ports of these two VLANsNote: In Linux, to establish a VLAN first, and the VLAN and the physical port bundle, the switch is two layer exchange, processing is a data frame, so as long as the previous two steps to achieve the same VLAN data exchange. In this example, adding a gateway is using this Linux as a three-tier interchange.Two. Linux acts as a router configuration1. Under Linux, turn on soft route forwarding1. Modify the configuration fi

The router's wide area network address could not be obtained, that is, the router page has been showing the connection status, IP address can not be logged on, resulting in the normal Internet access. How should this situation be resolved? The following small series share is the router WAN address can not get the solution. First you need to check the Internet bar router's WAN port led is already lit, if the WAN port led is not lit indicates a network cable or crystal head problem. At this point

1. To see if the wireless network card wireless router in the same room, if the interval is similar to the wall barrier, it is recommended that the wireless network card and router in the near distance barrier-free use of the case, determine whether the obstruction caused by the signal attenuation caused by instability. 2. If there are other wireless devices around, or microwave, cordless phone (2.4GHZ, microwave transmission of equipment) because of different wireless devices if the same or si

I believe you should all know that the different speed limits of the router are not the same, I will mainly for Cisco router settings, the details of Cisco router speed limit and its methods. Nvar speed limit of Cisco router BT software now blocked will automatically change the port, some software or use 8000, 8080, 2070 and other ports, restricting these ports so that the network is not normal, so to use NVAR (network-based application recognition, network application recognition) , Nbar (

is reached. To protect the compromised system from crashing, we can take the following two strategies: Filtering data using the Control access list The access control list is used on the network boundary router of the final attack target, and the ping attack packet is refused to be sent to the attacked host. But this is a rough way, because when you have completely limited the ping packets to the attacked host on the router, the other ping packets that you want to pass through normally will n

] ESP encryption-algorithm 3DES-CBC //ESP protocol uses an encryption algorithm for 3DES-CBC[H3C-IPSEC-TRANSFORM-SET-V7] ESP authentication-algorithm MD5 //ESP protocol uses the authentication algorithm as MD5[H3C-IPSEC-TRANSFORM-SET-V5] quit# Create a security policy template with a template named 1 and a sequence number of 1.[H3C] IPSec policy-template 1 1[H3c-ipsec-policy-template-1-1] transform-set v7 //Specify IPSec security offer for reference[H3c-ipsec-policy-template-1-1] Security ACL /

written as http://, with a colon: instead of a dot.: http.//192.168.1.1 The correct access method is input: http://192.168.1.1 or http://192.168.0.1 (HTTP can be omitted, that is, directly enter 192.168.1.1 or enter 192.168.0.1). Note that different brands of routers, the default IP access address is also not the same, and generally allow users to modify the default address. Therefore, please refer to the instruction manual for the specific acce

This site has previously shown us the method of segmenting a router into eight virtual routers using virtual Routing and forwarding (VRF, VM forwarding) through a scene example. I showed you how to configure VRF, and in this article we continue to use this scenario and, through IPSec configuration, replicate the exact topology and address to eight experimental environments. The entire environment can proceed smoothly, first requires the virtual route

off, you will not have any autodial connections. Since we want to be able to achieve autodial, set it to active, and then click the Execute button at the bottom right to save the settings. (Figure 1) The fourth step: after reactivating the broadband router, whenever we turn on the power of the device, he will automatically dial and connect the network, thus realizing the function of Internet automation, eliminating the user manual dialing operation. However, this automatic dialing s