-get update# Installation Driver$ sudo apt-get install nvidia-378 nvidia-settings
Note: Now laptop, especially use security boot mode to install Ubuntu. To properly install the driver, you must turn off security boot. Since and before installing Ubuntu, no cancellation code is set. It is required to set a verification code when installing the video dri
sudo add-apt-repository ppa:bumblebee/stablesudo add-apt-repository ppa:ubuntu-x-swat/x-updatessudo apt-get updatesudo apt-get install bumblebeesudo apt-get install bumblebee-nvidia sudo reboot
The above command is to install bumbleebee
Run the following command:
lspci |grep VGA
If the output is similar to the two rows:00:02. 0 VGA compatible Controller: Intel Corporation 2nd generation core processor family integrated graphics controller (Rev 09)
0:
will find that the error and warnning are not there before the logo on the boot.---Install Nvidia single display driver, reference help Http://fedoraproject.org/wiki/BumblebeeHere I install bumblebee, also install Nvidia's closed source drive, but the channel is not the same.According to help I toss for a long time, re-installed two times the system, only to find out the correct method. (The reload is due to the crash when restarting)Help Page said a
disk and try Fedora 21. In the Ubuntu Desktop System, installing the Nvidia graphics card driver is a matter of minutes, and it has been used smoothly. For details, see "desktop beautification" here. However, in ora, it has always been a tough task. Especially for workora 21 Workstation, installing the Nvidia driver on my laptop won't get any good results. No ma
1. go to the official download of the latest version of nVidia driver, the latest version is Nvidia-Linux-x86-270.41.06.run2. delete the previously installed nVidia Driver (skip this step without security) sudoapt-get -- purgeremovenvidia-* 3. this is found in the Nvidia official instructions, establish and modify the
It's been a long time today. Intel integrated graphics display. Finally it was all done, and here's a record.1. The first thing in the BIOS is to open Intel HD graphics. I set it up as the main video card, and the monitor is also connected to the port of the core graphics card. After restarting, I card warning low resolution, into the desktop 2. The command to switch the n/i card is prime-select (the installation package is Nvidia-prime, does not need
compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)It may be related to the video card Driver Upgrade.So I re-installed three nvidia-current nvidia-settings-updates packages.
Restart the computer and then execute lspci.
Www.linuxidc.com @ linux :~ $ Sudo lspci | grep-I vga[Sudo] password for jim:00:02. 0 VGA compatible controller: Intel Corp
In Win7, how does one delete the Nvidia icon? When using Win7, some users find that there is a green graphics card icon (Nvidia) in the lower right corner of the desktop, which is actually a quick way to open Nvidia graphics card management software, if you do not need this shortcut, you can delete the Nvidia icon as f
Failure phenomena:
How to adjust the display of contrast, brightness and other parameters through the Nvidia Control Panel.
Solution:
1. Right-click on the desktop blank position and select Nvidia Control Panel;
2. Select "Adjust desktop color settings" under "Display", then click on "Nvidia Settings" to adjust the brightness, contrast, grayscale and other
1. Search for "Additional Drivers" in Unity2. Open and select the following options3. Open the terminal and entersudo apt-get install nvidia-3614. Install the Intel graphics driversudo apt-get install Intel-microcode5. Run the "Additional Drivers" again and select the installed graphics driver: 6. Open the Nvidia X Server Settings and select the video card to switch:Http://www.linuxwang.com/html/2150.html"T
/s.Thanks to the new technology, new architecture, and new design, the power consumption of the whole-card thermal design remains at 250 W, with 8 + 6-pin auxiliary power supply.Another increase was the price of $1200, equivalent to nearly $8000, compared with $1000.However, you don't have the money to buy it, because the new Titan X is only available in Europe and America through the NVIDIA official website for the moment, and AIC vendors are not
Use Bumblebee to control NVIDIA dual-graphics card (ubuntu) introduction Nvidia dual-graphics card switching technology is called Optimus (Optimus Prime), but unfortunately it can only be implemented under win7 and vista. There is no corresponding technology in Linux, and of course Apple does not. This leads to the independent video card has been enabled, the video card fever, wind... use Bumblebee to contr
First, we asked a dealer who sells laptops for a long time and got the following answer:
Q: Do you need to activate your new laptop?
A: Need to activate, one or two times is enough, each time preferably more than 10 hours;
Q: So, how to properly charge? Some people say that every time you use the machine to automatically shut down and recharge better. Some people say, do not have to pay attention to, any time can do.
A: This does not matter, alway
, it was obvious that it was no longer hot.
However, the Nvidia Prime project has become increasingly mature. You can try Intel + Nvidia dual-graphics card. Nvidia Prime allows Linux users to switch between Intel integrated graphics card and Nvidia independent graphics card with a few clicks. Next, I will share with my
registry items provided by NVIDIA.
In addition,
1) NVIDIA's own chips have burned out on its laptop, and we can solve this problem without seeing NVIDIA update software.
2) NVIDIA has now abandoned geforce5500 and will stop production at the end of the year.Don't expect NVIDIA
(This article is intended for me who have failed several times and provide various incomplete solutions online)Step 1: Download the NVIDIA graphics card driver under Ubuntu
Cheungmine. All rights reserved. The source is reprinted. My scenarios are:
I have two computers, both of which are Windows 7 + Ubuntu11.10 64-bit dual-systems. One of them is a Dell desktop and an nvidia quadro 600 video card. The other
This article describes how to set up two laptops to enable wireless Internet access, and provides detailed configuration instructions and precautions. I believe this article will help you.
1. Two Local Wireless Internet access settings
The most convenient method is to use the new bridge function in Windows XP. Accessories: two local cables, one network cable, and adsl modem.
First, set the IP address of the wireless network adapter of the host to 192.168.1.1 and the subnet mask to 255.255.255.0.
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.