omap development board

A 51 Development Board was developed recently, as shown in. This board is very simple,All I/O ports are extracted, and Peripherals can be expanded by themselves. P0 is used to pull up the resistance,11.0592 M crystal oscillator, reset key, DC power plug, DC power self-locking switch, microcontroller lock seat, expansion of three VCC And Gnd. Compared with the lar

1. Do not use router switchesHardware connection:Connecting the Development Board to the PC using a network cableSerial cable connects the PC and the Development BoardUse the command:Ifconfig-aSerial port control to view the network configuration of the Development BoardRoute-nSerial Console view gateway settings for t

The card computer boom triggered by Raspberry Pi has also led to the development of small-sized card computers by embedded developers in China. The well-known embedded developer in China, tianyinao technology and Feiling embedded system, also developed card computers. Now, we will compare the basic parameters of the embedded E8 chip computer with the OK335xS-II Development

Here are my IP settings: Local Connection IP Address: 192.168.1.23 subnet mask: 255.255.255.0 Default Gateway: 192.168.1.1 nbs The following are my ipsettings:Local Connection IP Address: 192.168.1.23Subnet Mask: 255.255.255.0Default Gateway: 192.168.1.1Preferred DNS: 202.96.128.86Development Board IP Address: 192.168.1.230Subnet Mask: 255.255.255.0Default Gateway: 192.168.1.1Preferred DNS: 202.96.128.86Virtual Machine Ubuntu IP: 192.168.1.108Subnet

This article goes from Schindler to Forum:http://www.topeetboard.com1. Install ADB driverTo debug Android apps on the Development Board , first install the ADB driver. Installed through theSDK Manager.exe. As shown in. It is also important to note that if you want to use theThe SDK Manager installs the software and needs to shut down Eclipse. After the installation is complete, open thecommand line cmd.e

When running programs on the developer board, you sometimes need to debug to migrate GDB to the Development Board. First download gdb:http://ftp.gnu.org/gnu/gdb/, I choose the latest gdb-7.11, download after the decompression, the next is configured and compiled ./configure--HOST=ARM-LINUX-GNUEABIHF--prefix=/home/xx If it's a 64-bit system,--HOST=AARCH64-LINUX

By learning Android Deep Exploration (Vol. 1) HAL and Driver development in the fifth chapter to build the test environment of s3c6410 Development Board, I have mastered the method of building the test environment of s3c6410 Development Board1 Installing the Serial debugging tool: MinicomIn Ubuntu Linux, for example, y

Use of the environment: Win7 flagship 64-bit, VMWARE11 using the ubuntu12.04 provided on the board to open the virtual machine directly with VMware, since the development of the epc9600 Development Board, so the virtual machine network has been set, load ubuntu12.04 after the discovery can be directly networked .The cr

commands such as Snmpd,snmpwalk with the Arm-linux-strip command before porting9. Copy the Snmpd,snmpwalk to the Development Board/usr/bin, snmpd.conf and MiB folder and folder contents to the Development Board/usr/local/share/snmp/No folders created by yourself, note using chmod 777 Snmpd,snmpwalk10. Running snmpd-cc

Android Communication with Development Board1, because we use this experiment is the serial port 2, that is, the serial port 2 to the WiFi core board use, change the jumper cap, so that the original serial port 2 is provided to ZigBee use, instead to wifi use.2. Add ser2net ApplicationLast time we succeeded in allowing the driver to support the serial port 2, and did a simple test. Next, we will add an appl

It's okay. I 've been playing with the company's development board. One day I wanted to integrate Google Maps, so I started to take action. The process is summarized into the following steps: 1. Create a project named GoogleMap Based on Google APIs The content of several important engineering documents is as follows: 1) Layout file main. xml There are two points to note: I. mapview: similar to other views

CalibrationThe second correction process is DQS gating calibration. It is used to fine-tune the read DQS gating so that it can accurately capture the read DQS signal. The calibration program adjusts the DQS gating delay to find a valid DQS delay window in the 4/256-always cycle. Press ' y '/' n 'Intermediate operation similar, no longer translated Calibration ResultsAfter finishing all the calibration process, the calibration results is summarized and as shown below.? The tool would proceed to

Http://www.analogcn.com/news/wd/200711/20071121171437.html The Manual on the bf531 Development Board is a bit hard to understand:I am confused when I use the Super Terminal FTP on Windows PC and Linux PC FTP later.The manual says:(1) You must first transmit the program FTP to the Linux server.Which server is it uploaded? How can I get the username and password? Please tell me one. (2) After FTP is downloa

Generally, developers in development companies have different development boards at the same time because of Project iteration requirements. However, the USB of different development boards is different, which makes the adb unidentifiable. The following is a solution for Ubuntu. Step 1: Open the terminal and enter the usb id of our new

The previous article introduced the Http Server and accessed the Http service on the Development Board through the IE browser on the PC (equivalent to the Http client. This time, we implemented the Http Client on the Network Development Board to obtain weather information on the Yahoo website and display the informatio

Compile the Linux kernel of the NanoPi2 Development Board and nanopi2linux Compile the Linux kernel of the NanoPi2 Development Board. 1. Download The Linux4.4 kernel source code Git clone https://github.com/friendlyarm/linux.git // these steps need to be used in a linux environment, the download speed is slightly s

/wKiom1cy3v3SjVNEAABq49zVkfU338.jpg "title=" Picture 8.jpg "alt=" wkiom1cy3v3sjvneaabq49zvkfu338.jpg "/> If the input file address, as you u-boot-itop-4412.bin the actual address of this file, the of the output address, the actual device number of your TF/SD card is subject to.Here, you can insert the TF/SD card into the Development Board to power up, in order to prove that we are burning, we do the followi

MiS603 Development Team Date: 20150911 Company: Nanjing mi Lian Electronic Technology Co., Ltd. Forum: www.osrc.cn Website: www.milinker.com Shop: http://osrc.taobao.com Eat blog: http://blog.chinaaet.com/whilebreak Blog Park: http://www.cnblogs.com/milinker/ MiS603 Development Board the Fifth Chapter button to shake the experimentThe chattering of the keys means

input conversions, or 1 if an error occurs, otherwise 0 is returned;Iconv_close is to close the pipe (channel).If for a large number of encoding needs to be converted, the above function covert is not suitable for this way, one is the memory limit can not be called once, second, if multiple calls will frequently open a coded pipeline (channel), resulting in waste of resources, the best way is to take apart the function according to the situation use.Second, arm-linux transplant process1) http:/

First, install, configure, start FTP, SSH, or NFS servicesRefer to Vedon's complete manual for embedded Linux application development http://pan.baidu.com/s/1o79h3n0Second, Windows, Linux, and the Development Board need to ping the threeReference: Http://pan.baidu.com/s/1o8Uw0voNote: The Development