outside trunking

use. C. Support for VLAN functions: the Gigabit Ethernet switch supports Port-based and VLAN-based labeled 802.1Q tags, allowing you to comprehensively improve network performance. D. Support for port aggregation Trunking) function: You can use the Trunking function to bind several ports and provide a larger bandwidth aggregation channel between the switch and the switch, and between the switch and the ser

status VTP Version: 2 Configuration Revision: 7 Maximum VLANs supported locally: 1005 Number of existing VLANs: 8 VTP Operating Mode: Client VTP Domain Name: test VTP Pruning Mode: Disabled VTP V2 Mode: Disabled VTP Traps Generation: Disabled MD5 digest: 0xC7 0x2C 0x77 0x78 0x85 0x3B 0x00 0xF5 Configuration last modified by 0.0.0.0 at 3-1-9300: 01: 41 Switch2 #Show interface trunk Port Mode Encapsulation Status Native vlan Fa0/1 on 802.1q trunking 1

Cisco mds9222i Fibre Switch most commonly used debug commands1. Check the switch portShow interface [Interface-range]View specified port run status, WWN information, configuration parameters, and packet statistics.Demonstration:mds9222i-1# Show Interface FC1/1FC1/1 is trunking-port FC1/1 operating normally, is a TE portHardware is Fibre Channel, SFP was short wave laser w/o OFC (SN)-Port, SFP hardware informationPort WWN is 20:01:00:05:73:ad:2a:00-swi

convert UDP to TCP.The key to the Trun scenario is trunking (relay). This protocol relies on the trunking on the public network to ensure the visibility and availability of private web hosts ( figure 3-6). Figure 3-6 Turn Relay Server Both ends send an address assignment request to the same turn server, followed by permission negotiation. Once the negotiation is complete, both ends communicate

Introduction to Cisco Port Channel)Port trunking is used to bind multiple low-bandwidth ports of a vswitch to a high-bandwidth link to achieve load balancing. Avoid link congestion. Through configuration, You can bind two or four ports to forward data on specific ports to prevent packet loss when the forwarding rate of a single link is too low. Advantages of Trunking: The price is low, and the performance i

other is C 2948G-L3. The price of 2948 Gbit/s is good. It uses the same software as the Catalyst 5000/5500, with 48 10/100 Mbps adaptive Ethernet ports and 2 Gigabit Ethernet ports, 24 Gbit/s back-board bandwidth, redundant power supply with hot swapping, with a series of fault tolerance features and network management features. C 2948G-L3 is added with layer-3 switching capability based on C 2948G, and the maximum layer-3 packet throughput can reach 10 Mpps. However, in general, the 2900 serie

and the PHS standard to form the access network, because of their large capacity, the DECT can be compatible with the cellular system, But the PHS has the characteristic such as intelligence function. Also, "They can use a wireless band together in one location." However, with the development of wireless access network, the use of GSM and CDMA standards is more and more. And the relative proportion of wireless access network using radiotelephone Technology (Special DECT standard) is reduced.7,

able to boot your guest VM, and use Wireshark or whatever in the guest. Just remember! Your VM Guest ' s network Adapter must is set to bridged (connected directly to the physical network), not NAT (used to Shar E The host ' s IP address). 2.5 about VLANs in VMwareThere are three different ways to VLAN in VMware, see VMware ESX Server 3 802.1Q Solution: http://wenku.baidu.com/view/90b76687ec3a87c24028c4b9.html1, VGT in the virtual machine is labeled, the Port Group vlan_id property set to 4095

intermediate devices (or intermediate systems), the term ISO is called a trunking (relay) system. Depending on the hierarchy of the trunking system, there are five types of relay systems available: 1. The physical layer (that is, the first layer, layer L1) relay system, namely the transponder (repeater).2. Data Link layer (second layer, layer L2), which is bridge or bridge.3. Network layer (third layer, la

one channel fails, the Ethernet channel usually provides redundancy. This process is used PortThe aggregation protocol (PAgP) takes about 15 seconds. Trunk configuration test wired and wireless networks Next, VswitchStart testing this PortTrunk or not Port( VswitchInterconnected Port). TRUNKING Vswitch PortTo exchange data between multiple VLANs. For Trunk PortOf course, you can disable it and save 1 or 2 seconds. Vswitch PortAdaptive speed and f

simultaneously.Note:1. The SPAN dialog can only monitor data packets in the vswitch.2. The sc0 interface of the vswitch cannot be configured as the SPAN source port.3. The EtherChannel port cannot be a SPAN destination port.4. when configuring a SPAN dialog, if the Trunking mode of the target port is "On" or "Nonegotiate", the SPAN packet will be forwarded in the Encapsulation Format configured by the original Tr