packet tracer labs

Nat[network address translation] In the absence of IP address in the case of a great use, it can not be normal Sisu network of the intranet address into a legitimate external network address on the public network to send and receive data. At the same time address translation function can also be very good to hide and protect the host network.Nat has static NAT (internal address and external address one-to-one) and dynamic NAT (internal address pool and external address Pool A-do)This time we'll

Network address port Conversion NAPT is a very familiar way of transformation. NAPT is commonly used in access devices, which can hide small and medium-sized networks behind a legitimate IP address.Unlike dynamic address NAT, NAPT maps An internal connection to a separate IP address in the external network, adding a TCP port number selected by the NAT device to the address.This time, let's get to know napt.Configuration ideas1 Configure the router's interface IP address, note the network segment

RIP protocols can be configured in a more convenient way, but the limitations of RIP itself indicate that it is not suitable for medium to large networks. In contrast, OSPF is more complex to configure than RIP, but its functionality and performance are better than RIP.Configuration ideas1 Configure the physical interface address of the router Xia Lian switch and the physical interface address of the router to the other router and open the port2 Configure the address of the switch Xia Lian PC an

Tags: cal enhancement packet share image share access Cisco virtual SRCVLAN, the virtual LAN (Virtul local area network), the VLAN divides the physical connected LAN logic into different virtual networks, its existence can reduce the broadcast domain, enhance the network security and convenient and flexible networking, adding PCs and switchesBy configuring VLANs, you can implement PC1 and PC2 that are connected to the same switch and cannot communicat

Through the previous experiment we learned that by configuring VLANs, the terminals under different VLANs could not communicate with each other, but if you wanted to communicate between different VLANs, you would need to configure inter-VLAN routingLayer three switches have the capability of the network layer and can be forwarded via the routing functionNetwork environment1 set the IP address and gateway of the terminal (192.168.1.1 and 192.168.2.1, respectively).2 VLAN is configured under Layer

Cisco Packet Tracer version: 6.0.0.0045Single-arm routingVLAN planningConfiguration on Switch 0:switch>enSwitch (config) #vlan 2 #创建vlan2Switch (config) #vlan 3 #创建vlan3Switch (Config-vlan) #exitSwitch (config) #exitSwitch#show VLAN #查看vlanSwitch (config) #interface range F0/2-F0/4 #range可以批量选择端口Switch (config-if-range) #switchport ACC VLAN 2 #将这3个端口添加到vlan2里面Switch (Config-if-range) #exitSwitch (config) #e

Problem Description:Cisco Packet Tracer software configures switches in the CLI, routers enter information with IP type when entering "." The input character jumps to the first bit of the string or "." The front of the character.Terminal (PC, notebook, tablet) device in command prompt debug with IP type information the cursor will also jump.Workaround:Switch input method, especially can not use Sogou input

Cisco Packet Tracer 6.0 configures the Terminal Server method:Look at my topology first.650) this.width=650; "src=" Http://s1.51cto.com/wyfs02/M02/7D/6A/wKiom1bnyXWRIJP5AAAktArJM2M738.png "title=" capture. PNG "alt=" Wkiom1bnyxwrijp5aaaktarjm2m738.png "/>Server configuration:1, configure the IP address, and client side in the same network segment(config) #interface f0/0(config-if) #ip address 192.168.1.1 25

Tags: div forwards cer packet col out log other CISCBuild a network, the left LAN is 10.0.0.0 network segment, right LAN is 12.0.0.0 network segment, the middle is WAN 11.0.0.0 network segmentThe above success, but not very familiar with, the following again1. First create a network with a visual interface2. It seems that the computer must first connect with the switch to connect with the router3. The rest is very simple, configure the static route is

. Cisco router in the configuration of ports, or to understand the next few port names and purposes more meaningful, s port is the meaning of serial interface, also known as high-speed asynchronous serial port, is mainly connected to the WAN v.35 cable, commonly said routers and routers when used in connection. F port is a fastethernet interface, called Fast Ethernet port, mainly connected to Ethernet (LAN) used, the popular saying is to connect switches, computers, with the common twisted pair

Cisco Packet Tracer Experimental Tutorials This note is the experimental source of the school computer networks in the course of experimental data, I slightly collated some, in the implementation of the command line to add some comments, implementation is not unique, my implementation is not necessarily optimal, if there is mistake, please correct me; The following entries directly link to my note-takin

Tags: int range. com topology type mode config OSS processFirst, the experimental topology:Second, the experimental requirements:1, PC0 connection SW1, did not make any changes, see if F0/1 need to wait for 30s to become green;2, SW1 Global deployment of the default port Acceleration command, while the f0/2-5 deployed as Acess port;3, PC1~PC4 connection SW1, accelerate, the second into a green port, shorten the 30s, no longer wait.Third, command deployment:SW1 (config) #spanning-tree portfast De

Tags: tle simulates a trunk mode ace 51cto fast spanning tree quick typeLoops are present in the network, and all loops are formed due to confusion caused by ambiguous destination paths. The loop has a great impact on the network. Spanning Tree protocol is a good solution to this problem.The idea of spanning a tree protocol topology is that, regardless of the physical connection between switches, the switch can automatically discover a network with no loop topology, and the network of the logica

successfully and you can view your saved files on the TFTP server.4. Restore your configuration file, ping the TFTP server, keep the connection, download from TFTP to the routerCopy tftp running-config Download the previously configured backup from TFTP and restore the router's configuration fileIP address of the 192.168.1.1 TFTP serverRUNNING-CONFIG-BK you want to restore the backed up files in TFTPRunning-config a name for your recovered files.Final reload, successful restart, successful reco

---restore content starts---1. Simple LAN BuildSwitch: 2960 s1Terminal equipment: Generic PCConfiguration PC1 Click >>descktop>>ip configuration IP 192.168.0.1 255.255.255.0 port FastEthernet0 fastethernet 0/1PC2 Click >>descktop>>ip configuration IP 192.168.0.2 255.255.255.0 port FastEthernet0 fastethernet 0/2PC3 Click >>descktop>>ip configuration IP 192.168.0.3 255.255.255.0 port FastEthernet0 fastethernet 0/3PC4 Click >>descktop>>ip configuration IP 192.168.0.4 255.255.255.0 port FastEthernet

) #exit #退出接口配置模式Router (config) #exit # exit Global moderouter#disable# Exit Privileged ModeRouter>Configuring the Router serial interfaceThe serial interface is used to reach the router at the remote site or ISP over a WAN connection.Router>enableRouter#config TRouter (config) #interface serial 2/0Router (config-if) #ip address 192.168.20.100 255.255.255.0Router (config-if) #clock rate 56000# If the DCE cable is connected, set the clock frequency, or skip this step if the DTE cable is connecte