packet tracer simulator

What is Cisco Packet tracer?The Cisco Packet Tracer is a powerful network simulation tool for training in Cisco certifications. It gives us a good view of the interfaces of each router and network device, with many options, and we can use unlimited devices in the network just like with physical machines. We can create

Lab Environment:650) this.width=650; Tracer of "alt=" Cisco Packet EtherChannel increases link bandwidth and redundancy-Ibm.chick-mingkang.zhou "src=" http://img0.ph. 126.net/1inyhgrqquafdjfzpjjgsw==/6630808280955124494.jpg "style=" border:0px;height:auto;margin:0px 10px 0px 0px; "/ >Experimental Purpose:1. Observe the STP status of the two switches.2. Configure the EtherChannel, and add the physical port t

Packet Tracer 5.0 Experiment (eight) router static routing configurationFirst, the experimental target Master the configuration methods and techniques of static routing; Mastering the connectivity of the network through static routing method; Familiar with the connection mode of WAN cable; Second, the experimental backgroundSchool has new and old two campuses, each campus is an indepen

software name : Cisco Packet Tracer 6.2 for Windows Student VersionDownload Link:http://pan.baidu.com/s/1bn2WRmR password: J6JWSoftware:650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/74/FC/wKiom1YwOl6QeNW5AAXqwnnUQnA621.jpg "title=" 1.png " alt= "Wkiom1ywol6qenw5aaxqwnnuqna621.jpg"/>This article is from the "Piece of Cake" blog, please be sure to keep this source http://jiangbb.blog.51cto.com/88

Packet Tracer 5.0 Experiment (IV.) inter-VLAN routing with three layer switchesFirst, the experimental target Master the configuration of the switch tag VLAN; Master three layer switch basic configuration method; Master three-layer switch VLAN routing configuration method; Inter-VLAN communication through three layer switch; Second, the experimental backgroundAn enterprise has two

Experimental Objectives:Technical principle: Switch (config-line) # can set the console port and vty remote login passwordSwitch (consfig) #enable password 123123Switch (config) #line console 0Switch (config-line) #password 112233Switch (config-line) #loginSwitch (config) #line vty 0 4Switch (config-line) #password 1234Switch (config-line) #loginExperimental steps:New Packet tracer topology diagramOpen PC1

Packet Tracer 5.0 Experiment (i) basic configuration and management of switchesFirst, the experimental targetMaster the configuration and management of switch basic informationSecond, the principle of technologyThere are two basic ways to manage switches: in-band management and out-of-band management. The console port management switch through the switch is out of band management: This management m

Packet Tracer Introductory One, Packet tracer introductionPacket Tracer is an assistive learning tool released by Cisco, which provides a network simulation environment for beginners in learning Cisco Web courses to design, configure, and troubleshoot network failures. The u

Linux Network Application Programming Packet Tracer installation and interface introduction, packettracerIntroduction to Packet Tracer 1 Packet tracer is an auxiliary learning tool released by Cisco. It provides a network simulat

192.168.2.0/24 is directly connected, vlan3switch # 6. Set the default gateway of the host under VLAN 2 and VLAN 3 as the IP address of the corresponding virtual interface; V. Verification enable pC1 command prompt Packet tracer PC command line 1.0 Pc> ipconfigip address ......................: 192.168.1.2subnet mask .....................: 255.255.255.0default gateway .................: 192.168.1

-5-changed: interface serial/0, changed state to upr2 (config-If) # clock rate 64000r2 (config-If) # % LINEPROTO-5-UPDOWN: Line protocol on interface serial/0, changed state to upr2 (config-If) # R2 (config-If) # R2 (config-If) # exitr2 (config) # IP Route 192.168.1.0 255.255.255.0 222.0.1.1r2 (config) # endr2 # % SYS-5-CONFIG_ I: configured from console by consoler2 # Show IP routecodes: C-connected, S-static, I-IGRP, R-rip, M-mobile, B-BGP D-VPN, ex-OSPF external, o-OSPF, Ia-OSPF Inter Area N1

on fastethernet0/0 from loading to full, loading doneR2 # Show IP Route // route information after route redistributionCodes: C-connected, S-static, I-IGRP, R-rip, M-mobile, B-BGPD-OSPF, ex-VPN external, o-OSPF, Ia-OSPF Inter AreaN1-ospf nssa external type 1, n2-ospf nssa external type 2E1-OSPF external type 1, E2-OSPF external type 2, E-EGPI-Is, L1-is level-1, L2-is level-2, Ia-Is Inter Area*-Candidate default, U-per-user static route, o-ODRP-periodic downloaded static routeGateway of last res

Fastethernet0/ 4 ! Interface Fastethernet0/ 5 -- More --...!! End J. Help Information ① Switch #? Exec commands: 1-99 > Session number to resume Clear Reset Functions clock manage the system clock configure enter configuration mode connect open a terminal connection copy from one file to another debug debugging functions (see also 'undebug ') delete Delete A file dir list files on a filesystem disable turn off privileged commands disconnect an existing network connection enable turn o

Tags: Linux plugin note ref CER class CISC get HTTPS77652571Https://linux.cn/article-5576-1.htmlTurn on login issues78587383Execute the following script in the root directory of the softwaresudo ./set_ptenv.sh sudo ./set_qtenv.shYou must follow the steps.installed in the default/opt/pt if the fallback is reinstalled on the default path because the home directory is installedSome dependent librariessudo apt install libqt5scripttools5sudo apt-get install libqt5multimedia5-pluginsLinux installed un