pico atx

, steel plate quality is to measure a chassis excellent and bad important indicators, directly determine the quality of the chassis. Products of poor quality of the inferior chassis because of its poor stability, the use will create problems such as shaking, which will damage the hard drive and other host parts, affecting its service life, and electromagnetic shielding performance is poor, which is harmful to the physical and mental health of users. Tempered Glass side version although beautiful

style, and the glass products are very good impression, this chassis is very consistent with the taste of the author, but this chassis has different from the other chassis special, so select hardware to be around it to unfold. 　　Chassis size determines motherboard specifications Now that we have identified this 904 chassis, I will first take a look at this chassis to support which motherboards. By observation, the chassis supports the ATX,M-

location (figure ).　　　　The memory used by the motherboard is determined by the chipset, because the beiqiao chip contains an extremely important memory controller. It should be noted that some boards using the via and SIS chipset may support both SDRAM and DDR at the same time, but the SDRAM and DDR memory cannot be mixed.　　　　3. Power Supply and motherboard combination:　　So far, The ATX Power interface has completely replaced the traditional at Power

RDRAM use the 184pin interface. In fact, it is unrealistic to distinguish between 168pin and 184pin by the number of pins, but we can identify the gaps in the memory slot by identifying the gaps, and it is foolproof. The memory slots with 168pin have two asymmetric gaps between the center and the right. The memory slots with 184pin have only one gap.The RDRAM memory slot of the 184pin has two gaps on the symmetric position (figure ). The memory used by the motherboard is determined by the chip

the most basic and most important part of the computer. The motherboard is generally a 4-6-layer rectangular circuit board, the above installed the main circuit system composed of computers, there are generally north-south bridge Chip (some north-South Bridge Integration) BIOS chip, I/O control chip, keyboard and Panel control switch interface, LED connectors, expansion slots, motherboard and card DC power supply connectors and other components. The so-called motherboard structure is based on

three kinds: ATX/M-ATX/ITX, the following is a list. Board Board Type ATX: Published by Intel in 1995. As of 2014 is still the most popular DIY a family of specifications, this is what we call the Big board, all kinds of interface complete. MicroATX (M-ATX): A scaled-down version of the

power will be directly burned off. So the power of the best state of the work in the rated power state, the occasional overload is no problem, but also does not rule out the stability of the problem. Calculation of rated power of non-standard rated power supply There are also many power supply manufacturers do not indicate the rated power, although it is also in line with the norms, the feeling is still a consumer suspicion, it is necessary to let everyone use p=u*i calculation to know. You c

The plate type is mainly divided into: ATX (Standard type), M-ATX (compact), Μatx, MINI-ITX (mini), e-atx (Reinforced) E-atx (Reinforced: Extended ATX, long 305mm* width 330mm, as long as the length remains 305mm, and width of 244mm are called E-

supply is to convert a 220 v ac to a DC power available for the PC. Generally, the power supply converts an AC to 12 V, 5 V, or 3.3 v dc. 12 volt DC is used to drive a device with a motor, such as a hard drive and a CD-ROM drive. 5 V and 3.3 V output are used to supply different components on the system motherboard. Almost all currently used PC power supplies are at or ATX architecture power supplies. The main difference between the two is the number

the motherboard does not boot the solution: One, the suspicion of host power supply or bad First, the power supply, press the switch, if not power, and then unplug the main engine power, with tweezers to the Green Line and black lines short-circuit, look at the power supply fan does not, if the turn, indicating the power is good, failure in the host. Suspected host switch is good or bad: and then the ATX power cord and the motherboard, the motherbo

lines * postinst #! /Bin/sh 160 bytes, 5 lines * postrm #! /Bin/sh 379 bytes, 20 lines * preinst #! /Bin/sh 288 bytes, 14 lines * prerm #! /Bin/sh Package: nano Version: 1.3.10-2 Section: editors Priority: important Architecture: i386 Depends: libc6 (>=2.3.5-1), libncursesw5 (>=5.4-5) Suggests: spell Conflicts: nano-tiny (Replaces: pico Provides: editor Installed-Size: 1108 Maintainer: Jordi Mal

From: http://www.picocontainer.org/Two+minute+tutorial Two minute tutorialTwo-minute tutorial Authors:Jon tirsen This very short tutorial shocould get you up to speed with picocontainer in 2 minutes. It does not go into why you shocould do it, readFive minute IntroductionFor that.This is a very short two-minute tutorial on how you can quickly learn about micro-containers. If it still cannot be determined why you want to use micro-containers, you can continue to read the 5-min

very high sales of the pro-people starter game box, with Meng Meng's lovely shape, the most suitable for those who like to Meng things and like the simple family or office clan. In addition, the air fine great White chassis also perfect support ATX type (compatible with ATX,M-ATX,ITX motherboard), thermal performance is outstanding, the most importa

dependency injection mechanism, the key is to understand the container implementation method. The container reference implementation provided later in this article is the code of Mr. Huang zhongcheng. I only added some key notes here.2.1 constructor injection (constructor injection)We can see that in the entire dependency injection data structure, the important types involved are serviceuser, serviceprovider, and aggreger. The constructor mentioned here, it refers to the serviceuser constructor