psc printer

The first type of problem is that ink is weak, and this situation occurs in two cases, one is a single ink printer, and the other is a dual-cartridge printer. The most fundamental way to solve this problem is to add ink, the ink cartridge will be taken off the tip of the bottle with a sharp mouth into the printer cartridge ink plus ink. Check the print quality ag

The computer is connected to a shared printer and the prompt "operation cannot be completed." The printer name you typed is incorrect, or the specified printer is not connected to the server. For more information, please help ", what is the cause of this and how to solve it?" Computer network card's IP and shared computer name is not uniform General shared prin

One, the printer jam reason: Paper Jam is one of the most common printing failures in daily printing, with the following three main causes of paper jam: The use of poor paper or paper damp If there is no problem checking the printer part, the most likely problem is the paper. Poor paper often attached to a lot of confetti, the printing process of confetti into the machine, thereby causing pressure to rub

Step 1: Check the hardware Many printing problems are caused by incorrect hardware settings. Here is information on how to insert the cable into the correct location and ensure that the printer is powered on. Check that the cable is properly connected Check to make sure that the printer's power cable is plugged into the power jack and that the printer cable is properly connected to the computer from the

Step 1: Check the hardware Many printing problems are caused by incorrect hardware settings. Here is information on how to insert the cable into the correct location and ensure that the printer is powered on. Check that the cable is properly connected Check to make sure that the printer's power cable is plugged into the power jack and that the printer cable is properly connected to the computer from the

different computers, their identification of the printer category is different, many times there will be such a situation, the same printer, in this computer can be installed to drive, and the installation failed to change the computer. What if the Win7 printer fails to install? The following small series to introduce the next Win7 can not install

Many times, we need to install a printer in the office. This time, you need to drive life. Drive the Life Peripheral Drive section to support users to add network printers when there is a network. Usually, you can go through: Click Add Network Printer-drive Life Auto Search network printer driver-click Next to install the network

Many printing problems are caused by incorrect hardware settings. Here is information on how to insert the cable into the correct location and ensure that the printer is powered on. Check that the cable is properly connected Check to make sure that the printer's power cable is plugged into the power jack and that the printer cable is properly connected to the computer from the

shared printers are a common way to use printers in small office environments. On the WinXP system all know how to set up Printer sharing, on the Win7 system computer, there are many users do not know how to set up, shared printer settings become complex. So how do I set up printer sharing? Let's talk about Win7. Set the method for

See if your Windows 7 and Windows XP Two computers are connected to the same LAN, the general small office will be a LAN. And make sure your printer is connected to the Windows XP system computer and is shared. 1, after doing a good job, open your computer to install Windows 7 system, connect to the same LAN as the XP system. Open the Control Panel, locate "Device and printer" and click it.

How to choose the needle printer: To understand the areas that need to be applied, to consider its reliability, check performance indicators, durability, after-sales service. Method/Step First, understand the areas that need to be applied. Different applications need to buy different needle-type printer, needle printer has been divided into general

What if the printer is garbled or does not print? Answer: The following steps can be used to determine the fault: 1, the printer self-test: The printer alone, put a piece of paper, and then let the printer self-test (can refer to the use of the manual), to observe whether the printing results are normal. If the self-

For office supplies, printers are essential equipment in the office. But there are so many employees in an office, it is impossible to configure a printer for everyone, this time will be sharing the printer. Windows XP system How to set up Printer sharing, this article will be detailed for you to introduce! Simple setting of home network environment in general,

Booz Postek c168 Barcode printer has three LEDs and three keys in the lower left corner. Compared to other single LEDs and key design commercial printers, Booz C168 series recognition and operation will be more clear and simple, more humane. Booz C168 Series three indicator lights and three function key design, you can remind users of the current machine working state, and press a key to perform the required function settings. For example: Ready ligh

The new HP DeskJet 2131 inkjet printer, according to the instructions installed after the installation of the computer, the discovery Scan, copy function is normal use, except printing function can not be used normally.The problem is as follows: Print the test page in the installed printer Assistant can output normally, but the Print button in Word will not print properly, although in the Print list can se

Getting started with Linux: Installing a brother printer in Linux Q: I have a brother HL-2270DW laser printer and I want to print documents from my Linux machine. How can I install a proper driver on my computer and use it? The brother's brand is famous for its affordable compact laser printer. You can get high-quality WiFi/Duplex laser printers at a price less t

A day, after upgrading the bios of the motherboard, the original use of a good printer suddenly strike, even the test page can not print. The normal situation is that after the BIOS upgrade, peripherals should work better, this situation really makes me this "shrimp" feel helpless. Had to ask a friend to help, check all the parameters to get the settings, did not find the problem. Finally the printer "big u

Build a printer monitoring server using Nagios Tutorial Background: The company has many HP printers, which are difficult to manage. So I thought about whether I could be a printer monitoring server to quickly respond to all the printer problems. After that, I checked the relevant information on the Internet and set up one, so there was no problem in using it. I