Tags: Raspberry Pi ifconf auto start apt CTI no log art tarStart a Raspberry Pi 3B installed ubuntu 16.04 need to use the SSH record0. Get the Raspberry Pi IP firstRaspberry Pi uses a n
Prepare
Raspberry Pi Development Board ( Click here to purchase ) (has been brushed into the official Raspbian system )
USB to Serial board ( click here to buy )
DuPont Line (4 root)
Connection
串口板 树莓派--------------------VCC +5V(非必须)RX TXD(GPIO15)TX RXD(GPIO14)GND Ground Raspberry
make these aliases take effect later.
Command lines starting with "#" are commented out. To enable them, you only need to remove "#" And wait until your Raspberry Pi starts to activate these settings.
The. bash_aliases file is also referenced here. By default, this file does not exist:
If [-f ~ /. Bash_aliases]; then.~ /. Bash_aliasesFi
The if condition is used to check whether the file exists between the
An intranet map using peanut shells on Raspberry Pi (raspberrypi).One, Raspberry Pi environment
Operating system:The download link for the system image.
Hardware environment:Raspberry Pi Model B +
Second, the required software
Peanut Shell
ObjectiveIn the previous article, "Raspberry pi set automatic dialing, build no-line by environment" , the author uses HOSTAPD and UDHCPD programs to create wireless hotspots to achieve address assignment and DNS server settings. This article will make improvements to the Raspberry Pi AP based on the previous environme
We have explained in detail the Raspberry Pi control ultrasonic module ranging (http://www.cnblogs.com/yuemo/p/8888342.html) and ultrasonic control buzzer module audible (http://www.cnblogs.com/ yuemo/p/8906111.html).Today we'll see how to apply all two modules and make an anti-theft device.First look at the connection of each pin (requires seven mother-to-female DuPont line):Ultrasonic module:1.VCC: Connec
This project uses Raspberry Pi with ultra-low-cost software radio (SDR) hardware to receive tracking information sent from an airborne S-mode transponder outside millions of miles. The Raspberry Pi is equipped with a smart 3.5-inch TFT display to provide a convenient overview of aircraft activities.
HardwareThe r
NOOBS SETUPTo get started with Raspberry Pi need an operating system. NOOBS (New out of the Box software) are an easy operating system Install manager for the Raspberry Pi.How to GET and INSTALL NOOBSBUY A preinstalled SD CARDThe easiest-to-get NOOBS is to buy a SD card with NOOBS preinstalled, available-for£4 at the Swag Store. Alternatively, if you have a SD ca
Is Raspberry Pi able to use the serial port? The answer is yes. The specific method is as follows:
1. The third, fourth, and fifth ports in the first row of Raspberry Pi are respectively, that is, ports 6, 8, and 10 are respectively, TX and RX, respectively, and connected to the connected device. Note that the TX of
Do you have an idle mobile hard drive or Raspberry Pi? You can use these to create a cheap and low-energy NAS. The final effect is definitely not as good as the NAS for $500, such as those produced by Synology DiskStation. But you can build a low-energy network storage platform-and especially suitable for those who are tired of the National Security Agency's data monitoring, you can store the data in this "
The dynamic IP address of the Raspberry Pi was not read before Windows7, so moved to Ubuntu,The Raspberry Pi is plugged in, a network cable connects both ends (PC, Raspberry Pi)Ctrl +alt+t Open TerminalSu and switch to root userIn
0. PrefaceWhy do you want to use cross-compilation for "1"
The speed at which the cross-compilation tool is developed faster. The Raspberry Pi has already installed the GCC toolchain, which can be compiled directly from the Raspberry Pi source code to generate the executable file. At the same time, the PC can also use
1 , configuration options:The first time a Raspberry Pi is used, a simple configuration is required to run the following command in command-line mode:$sudo Raspi-configThe new and old version of the configuration interface is not the same, the following list of two kinds of more common:
Expand_rootfs – Extend the root partition to the entire SD card (the Raspbe
If you're bored with a smart home that just has to download a specific app to control a light, here's the good news: Openhab can give you the most flexible control of smart home, Openhab is a mature, open source home automation platform that can run a lot of software, There is no agreement, which means it can now be connected to almost all of the home automation hardware on the market.Here we will show you how to install and launch the free smart home system.We first use
Environment: Raspbian-stretch (2018-06-27)Raspberry Pi: 3 generation B Type1, Raspberry Pi equipment, need to be in the field can also have independent networking capabilities, it is necessary to use the Internet of Things module.The SIM868 communication module for micro-snow is used here, such as:2, will SIM868 insert
The latest version of the 2017-03-02 version of the Raspberry Pi system does not directly SSH login issues
Last night when installing the latest Raspbian system using Raspberry Pi 3 (2017-03-02), there was a problem:
There is no HDMI monitor on hand, so you can only use SSH to connect to the
Problem: "Unable to connect because the target computer is actively rejecting"
The first time to make Raspberry Pi, because the Raspberry Pi can not directly connect the monitor, so use remote connection, here, I use a network cable to connect the way, notebook and Raspberry
Raspberry PI Series--bare metal illuminated LED lightsBackgroundRecently just bought Raspberry PI B +, configured to run the official Raspbian system, tossing a week Linux system, feel no meaning, so try to understand the bottom of the start process, through a few days of research, It is found that the boot of the lowe
In this article you can learn: Berryboot use, Kali installation, open-hung mobaxterm, and tips on mounting via label and UUID. This article defaults to the Linux Foundation you have, and also for the level of just getting started, because this is my toss record. Do not know can leave a message or email. The first thing to be clear is that now is not completely out of the SD card method, because PI is the default from the SD card boot. Just realized pu
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.