system errors automatically" and "scan and recover bad sectors", then click Start.
The scan time varies depending on disk capacity and scanning options. It is worth noting, however, that in Windows98 or even above operating systems, the details of each sector are not shown, so it is often preferable to choose DOS Disk Detection Tool ScanDisk in this case. ScanDisk detects each sector and marks bad sectors so that the operating system continues to ac
table to record the starting or ending address of the partition. The corruption of these data will cause confusion or loss of the partition, it is generally not possible to manually recover, the only way is to use the Backup partition table data to write back, or from the other same type and partition status of the same hard drive to get the partition table data
to repair, select Properties, click the Tools button in the dialog box that appears, and click the Start Check button in the Error checking option group. In the dialog box that appears, select the Automatically fix file system errors, scan and attempt to recover bad sectors option, and click the Start button.
By means of the above method, the logical bad path problem of hard disk can be solved generally.
, which must be based on the hard disk conditions to set up, otherwise it is likely that there will be other problems. This kind of situation is not difficult to solve, as long as the motherboard BIOS instructions and the hard disk itself, the correct settings can be resolved.
Third failure: A primary partition fails to start the hard
There are two fault prompts for Hard Disk Self-check by microcomputer: "HDD Not Detected (Hard Disk Not Detected)" and "HDD Control Error (Hard Disk Control Error) ". The following describes how to fix the vulnerability.
First, wash your hands with water to clean the oil and sweat on your hands. At the same time, remove potential static electricity from your bod
People who use laptops may have encountered unreadable data and failed to identify hard drive failures such as hard drives. So what are the causes of these failures? How to solve it after the appearance? How to recover data loss caused by hard disk damage? After consulting p
disk is not formatted, it is displayed as an invalid drive. If you understand how fdisk works, you will know that fdisk only rewrites the content in the primary Boot Sector of the hard disk (0-sided 0-Sector 1-sector). Specifically, it deletes the partition table information of the hard disk, the data in any partition on the
. If the program is damaged, it cannot be booted from the hard disk, but the hard disk can be read and written after being started from the soft drive or optical drive. The solution to this fault is relatively simple. It is most convenient to use the FDISK of the higher DOS version. When the FDISK with parameters/mbr i
of the active partition. If the program is damaged, it cannot be booted from the hard disk, but the hard disk can be read and written after being started from the soft drive or optical drive. The solution to this fault is relatively simple. It is most convenient to use the FDISK of the higher DOS version. When the FDI
Vista itself carries a better use of gadgets to scan hard drive lookup errors.
The specific steps are as follows:
(1) Open my "computer" and find a free disk.
(2) Properties-> Tools tab-> Click the check box next to "Automatically fix file system errors" and "scan and attempt to recover bad sectors."
(3) We can all choose between the two. -> started.
(4) It
words.Hard drive a day is not right, finally one day, the CPU said: "What is the next instruction?" "I looked, startled:" FORMAT ""What is it?" "The CPU is excited, this mindless guy.I still told him. I don't know why I'm doing this.Hard disk hesitated for a long time, finally said a track 0 bad,disk unusable.The electricity stopped, for a long time, I counted the clock in the darkness ...One months later the har
when a second hard drive is damaged in raid. This is the system crashes, data loss, the site can not be accessed.
Dedicated servers with a hard disk rack, the server can be hot-swappable SCSI hard drives without shutting down the computer, or you can replace the hard
selected to start with the second hard disk). The result is that there is only one vertex and one cursor in the upper left corner of the screen, this method failed (only my computer has failed like this. If some netizens have succeeded like this, you can try it );
Then I checked the information on the Internet and asked a netizen, So I installed an EasyBCD in win7,
Then restart the computer and you will see NeoSmart Linux. (You can change the name
the device in the window that appears, remove the device option from the system, and then unplug the hard drive from the host (remember not to unplug it when the hard drive is read or write). Otherwise very easy to damage the notebook computer hard disk).
3. Even in the no
data recovery software, invincible data restoration software and so on. These softwares are specially used to recover the data loss in the case of mis-deletion, partition loss, MIS partition, PQ operation failure and so on, the operation is simple, can scan the file slices deeply, and the recovery success rate is high.Of course, professional data recovery company, security is more secure, recovery success rate is also higher. For example, generally f
automatically" and "scan and recover bad sectors", then click Start.
The scan time varies depending on disk capacity and scanning options. It is worth noting, however, that in Windows98 or even above operating systems, the details of each sector are not shown, so it is often preferable to choose DOS Disk Detection Tool ScanDisk in this case. ScanDisk detects each sector and marks bad sectors so that the operating system continues to access the area.
can be resolved.
Third failure: A primary partition fails to start the hard drive
The hard drive has a primary partition in which the primary partition is started, and if the primary partition is faulty, then the system cannot be booted from the
ArticleDirectory
Memories of Linux installation on netbook hard drive (pure cainiao experience)
Memories of Linux installation on netbook hard drive (pure cainiao experience)
In, I installed the WINXP + linuxmint dual system on my netbook and deleted the G disk on Windows XP. The
, sometimes recognize the disk and sometimes blue screen.2, hard drive rotation, recognize the partition is slow or can identify some partitions, usually hard drive bad sector failure, due to natural life, head aging, minor fall injury.3, the hard disk does not turn, no soun
provide a shortage of current situation, we can according to their own host of the hard disk, optical drive and related configuration to calculate the full load of the power required to work, and we use the power of switching power supply compared. In general, the power supply should be greater than 10% of the maximum power of each component, but not the same.
Four, the
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.