remote access vpn configuration on cisco router

:(1) Step 1: Configure the Router Ethernet interface IP address(2) Step 2: Configure the router password(3) Step 3: Access the router via TelnetCommands for the relevant steps:Configure the Router Ethernet interface IP address (enter the privileged mode, global mode, interfa

strategy management in the remote access model and study the management system. 2 IPSec VPN The IPSec protocol provides interoperable, high-quality, cryptographic-based security solutions for IPV4 and IPV6. Including access control, connectionless integrity, data source authentication, prevent replay attacks, inform

Implementation of ADSL access using the cisco 2500 router Description: This case is Beijing Telecom's adsl PPPoE access. A common adsl modem and a cisco 2500 router (dual Ethernet port) are required, and IOS 12.2 (15) t, can achie

Build PPPoeServer with the home ADSL line and use the CISCO router to enable the PC to access the Internet www.2cto. comR1 (config-if) # doshrunBuildingconfiguration... Currentconfiguration: 1470 bytes! Version12.4servicetimestampsdebugdatetimemsecservicetimestampslog Use the home ADSL line and use the CISCO

Use the home ADSL line and use the CISCO router to build the PPPoe Server so that the PC can access www.2cto.com R1 (config-if) # do sh runBuilding configuration... Current configuration: 1470 bytes! Version 12.4 service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption! Hostname R1! Boot-start-markerboot-end-marker

Application (ACL) of the access control list of cisco router Integrated Experiment ii ip Address Configuration on each device, steps ======================================================== ========================================================== ======================================= Configure route R1: (config) # ip route 0.0.0.0 0.0.0.0 192.168.1.254 route

The computers in the 172.16.4.0/24 network segment are servers, and we protect these servers from the virus attacks from the 172.16.3.0 network segment via reverse ACL settings.Configuration instance: Prohibit virus from 172.16.3.0/24 this network segment to 172.16.4.0/24 this server network segment.Access-list Permit TCP 172.16.3.0 0.0.0.255 172.16.4.0 0.0.0.255 established Cisco Simulator defines ACL101, allowing all calculations from 172.16.3.0 net

Tags: switch 9.png edit Host route nbsp Computer Configuration Cer linExperiment Name: Cisco Remote Access Lab reportExperimental topology: Lab Preparation: One router, two switches, two computersExperimental purpose: Enable PC0 to access the switch remotelyExperiment steps

First, in the Cisco Remote Access server, with three pairs of lines to connect the DTE and DCE, each pair of lines, one sent, a receipt: 1. TX/RX Data transmission Line Send: Dte->tx->dce Receive: Dte DCE device (MODEM) sends data to DTE via RX, receives data from DTE via TX, sends The rate of reception is set on the modem. The modem and

Cisco Access Control Server Remote Denial of Service Vulnerability (CVE-2015-0746)Cisco Access Control Server Remote Denial of Service Vulnerability (CVE-2015-0746) Release date:Updated on:Affected Systems:

Demand:Use an extranet PC (Win7 operating system) that can be connected to the Internet. Remote access to the MAC computer under the public network Tp-linkEnvironment:Mac OS-----tp-link-----------pcTools:Putty TightVNC or TeamViewerMethod OneMethod One:Use TeamViewer 9. A fool's interview. It is important to note that the version number needs to be kept up-to-date, otherwise it will cause no connection. Thi

Home put two computers, in one of the Taichung did a website, but there is no domain name, want to let students visit their results, but the local address is 192.168.1.2 such an address is not possible to make extranet access, which is the router's internal allocation of IP addresses. This problem bothered me for a long time, and now finally got a trace of understanding and solve. First landing router to f