repair dead hard drive

. If the program is damaged, it cannot be booted from the hard disk, but the hard disk can be read and written after being started from the soft drive or optical drive. The solution to this fault is relatively simple. It is most convenient to use the FDISK of the higher DOS version. When the FDISK with parameters/mbr i

the Drive boot system. You can use FDISK to reset the active partition for repair. If a partition type is incorrect, the loss of a partition may occur. The fourth byte of the partition table is the partition type value. Normally, the basic DOS partition value larger than 32 MB is 06, and the extended DOS partition value is 05. Many people use this type of value to encrypt a single partition and restore the

format. Ghost also has a killer, which is to repair the hard disk's bad sector. I used to ghost a hard drive to get it done before long. The thing is this: I get 120 g of hard disk from friends, connect to the computer but found that the

example, the hard disk type in CMOS is less than the actual hard disk capacity, then the sectors behind the hard disk will not read or write. Need to reset or discharge the data in the CMOS. 5, the specific operation: turn on the computer or restart the computer, in the screen display "Waiting ...", press the "Del" button can enter the CMOS settings interface.

ArticleDirectory Memories of Linux installation on netbook hard drive (pure cainiao experience) Memories of Linux installation on netbook hard drive (pure cainiao experience) In, I installed the WINXP + linuxmint dual system on my netbook and deleted the G disk on Windows XP. The

hard drive has a physical bad way to do HDD has a physical bad way solution one: For the physical bad, the average user can not repair, the only thing we could do is to use some disk software to separate it into a single area and hide it, so that the head no longer read it, which can extend the hard disk life to some

to repeatedly replace the hard drive jumper and the optical drive jumper until all can be found. 5. There is also a special situation, for the motherboard has done diskless system, in the CMOS settings changed, need to be based on each brand of the motherboard to adjust, but will not adjust also does not matter, tell a very simple way: the motherboard battery t

course, even if the drive C cannot be read, we can use the fdisk/MBR command. In fact, fdisk/MBR has a very obvious role. It can also deal with some primary boot zone viruses, which can be well utilized by everyone, this is the first tool that can be identified by hard disks in the bios and cannot be operated under DOS. Apart from this hidden parameter of fdisk, you can also use the DOS tool fixmbr. After

Jumper (English jumper) is a small switch that controls the current flow on the circuit board. Its role is to adjust the equipment on the different electrical signals of the relationship, and to adjust the operation of the equipment, such as the motherboard voltage, drive master-slave relationship and so on. The jumper is basically composed of two parts, partly fixed on the motherboard, hard drives and othe

What to do if the computer doesn't recognize the hard drive: First check the hard drive master and subordinate line settings are set wrong, the master-slave line set incorrectly will cause the system can not be correctly identified. Test if the system can boot from the optical

Not all computers are equipped with DVD Rom, which makes it difficult to install Windows 7 on the computer. Windows 7 cannot be installed on the optical drive, or you can use a USB flash drive to install Windows 7. However, USB flash drives are not supported by all computers. You can only use the hard disk installation method. Before that, XP and Vista can direct

normally. This is not necessarily "bad", usually with the MBR removed and 70% better to repartition. Second, can be normal partition, can be formatted, but the scan found that there is a "B" marked, that is, usually called "out of the bad way." There is no "physical bad way" or "Bad Logic", "B" a small number of words (less than 100), basically 80% can be fixed as a "good hard drive." Three is not normal p

Since the floods in Thailand a few years ago, the price of hard drives has been strong, by the end of 2013 has not recovered to the previous historical minimum, and now the 500G new disk is also maintained around 300RMB. By the way popularize common sense, also be remind friends, buy new hard drive now, if purchase capacity under 500G, that must be refurbished d

What to do when the computer starts to read the hard drive Computer boot does not read the hard drive solution one: 1 Hard drive data cable or power cord interface loose. 2 The hard

What about the hard drive noise? Hard drive Noise Solution one: It could be a hard drive, but you said it was a big new buy, but it's still possible. How to Differentiate Listen to the sound can be very harsh, (if it is a slig

Welcome to the Windows Community forum, interactive communication >> access with 3 million technical staff One of the best ways to improve your computer's performance is to optimize your hard drive. The features included in Windows help you optimize the various types of drives that your computer uses today. No matter what type of drive your computer is using, Wi

I am a hard disk.Work on an ordinary desktop. People always think that we are high-tech white-collar workers, work clean and decent, seems to be very beautiful. Perhaps they are because they see the white and beautiful chassis have such an illusion. In fact, a small desktop like ours, the work environment is very narrow, the dust in the inside frightened dead. Everyday life backwater, work mechanically repe

We need to enter the computer's "Disk Management" into the processing, such as we press win+x will play the hard drive management interface, and then, like us, select C Disk then we then right-click it and then pop-up menu click "Properties"; Then we find the "tool" under the "error" into the interface and click "Check" under the "Repair

is not too late)The following are the methods and procedures for writing the Seagate K9K10 disk after the calibration is completed:First of all: Back to the AGE50 state. Use the R command to determine if the hard disk basic resource file module is properly loaded into memory (if you go directly back to t> to indicate normal)The judgment here is that if the error is usually the firmware area still has problems, basically need to recalibra

the mobile hard disk USB connection is good, we look at the host USB reception is not good, change the interface to try , the front is not good, change back to try again. PS: Some computers because of the front USB interface and not connected to the motherboard interface, resulting in the front USB interface is not available a lot, so this also need to pay attention to. ② when making sure that the computer host USB interface is available and the da