Install the RTL8188CE NIC driver (MercuryMW150U) in linux. first, describe my system: Ubuntu11.10kernel: 3.0.0-32-generic. today I bought a wireless network adapter Mercury150MbpsMW150U series, I found that the driver does not need to be installed in Ubuntu12.10 of my notebook... install the RTL8188CE NIC driver (Mercury MW150U) in linux)
First, describe my system:
Ubuntu 11.10
Kernel: 3.0.0-32-generic
Check the model of the local wireless network card by command first.[Email protected] desktop]# LSPCI02:00.0 Ethernet Controller:realtek Semiconductor Co., Ltd. rtl8111/8168b PCI Express Gigabit Ethernet Controller (Rev 06 )05:00.0 System Peripheral:ricoh Co Ltd Device e823 (rev. 07)06:00.0 Network Controller: Realtek Semiconductor Co., Ltd. rtl8188ce 802.11b/g/n WiFi Adapter (rev 01)
Find the Driver Model Linux driver on the Realtek website.Www.rea
CSCL RTK Point Calibration, CSCL RTK point translation, CSCL RTK single point correction step, how to use the CSCL RTK point calibration,Hand-thin Model: IHAND20 Android system hand-thinSoftware: Hi-survey Road\elecInstrument: CSCL company arbitrary RTK ProductsUse two point
RTK measurement system, generally need to first set up a reference station (reference station), data chain mode plug large radio (antenna power mode, ideal range within 18 km). The base station calculates the current position by receiving a satellite (multi-Star).This involves the setting of the frequency, the baud rate, and the protocol (commonly used tempo protocol, transparent protocol, etc.).These parameters are set to the output to the mobile sta
CSCL Kunming Technology Original December 20, 2016 updateCSCL RTK lofting point data into the hand thin,Hand-thin Model: IHAND20 Android system hand-thinSoftware: Hi-survey Road\elecCSCL RTK lofting Point data import hand thin description1 , make a copy of the loft point coordinate data to a thin memory.① Edit the loft point file in Excel, and the columns are called name, N, E, Z,Attention:Column order must
CSCL RTK Use instructions, CSCL RTK built-in network, CSCL network RTK, CSCL RTK using mobile card built-in network how to setHand-thin Model: IHAND20 Android system hand-thinSoftware: Hi-survey Road\elecInstrument: CSCL company arbitrary RTK ProductsHow to set up the built-
CSCL Kunming Technology Original December 20, 2016 updateCSCL RTK Control point data import hand thin description1 , make a copy of the control point coordinate data in the hand thin memory① edit the control point file in Excel, each column is named, N, E, Z,Attention:Column order must be: " name, N,e,z", no elevation, Z cannot empty, fill 0② Save as " Control point . csv" (comma delimiter ) ③ using a USB cable to connect the hand thin④ Open USB Stor
Middle Hai da RTK Hand Thin New project descriptionFirst, by the app to start the thin hand softwareHand thin boot, press app to start the thin hand softwareSecond, the new project① Entry InformationProject Information interface② project name input 0401 (date of day)③ Click OKAutomatically switches to project Settings \ System interface when the point is determinedSecond, set the coordinate systeminto the coordinate system or(1) projection selection G
gps1\gps6 control points in turnCalculation parametersProject → parameter calculation →Add → source point → point in library → Select gps1→ target point from coordinate point → select GPS1 from the Control Point LibraryAdd → source point → point in library → Select gps6→ target point from coordinate point → select GPS6 from the Control Point LibraryCalculation → See if the scale K is close to 1 (1.000 or 0.999)?Scale k is close to 1, point applicationNot close to 1, point No, check the control
Real-time kinematic real-time dynamic difference method. This is a new and commonly used GPS measurement method. Previous static, fast static, and dynamic measurements all need to be calculated afterwards to achieve centimeter-level accuracy, the
server after the transplant , execute the following statement to enable the serviceNamed-c named.conf -C refers to the file address of the configuration script named.confNamed.conf mainly has the following contentZone "localhost" in {Type master;File "Localhost.zone";allow-update {none;};};Zone "0.0.127.in-addr.arpa" in {Type master;File "Named.local";allow-update {none;};};Zone "test.com" in {Type master;File "Test.zone";allow-update {none;};};Zone "." {Type master;File "Rtk.zone";allow-update
My small wireless network card is Lenovo e420, and the wireless network card is RealTek rtl8188ce
Find the driver corresponding to omnipeek on the RealTek website. The URL is as follows:
Http: // 152.104.125.41/downloads/downloadsview. aspx? Langid = 3 pnid = 48 pfid = 48 level = 5 conn = 4 downtypeid = 3 getdown = false downloads = true # rtl8188ce
Rtl8188ce
= lwp::useragent->new; $ua->agent ("mozilla/5.0 (Windows NT 6.1; rv:30.0) gecko/20100101 firefox/30.0 "); In this way, the browser inside the request header becomes Firefox, and the server will think we are using Firefox. Do not forget cookies oh. My $cookie _jar = http::cookies->new (file=> ' lwp_cookies.txt ', autosave=>1, ignore_discard=>1); $ua-> ; Cookie_jar ($cookie _jar); Then call UserAgent's post and get method and do whatever you want. If you are not very clear, here is an example of
Recently to do a project on RTK, the use of Rtklib source code based on the transplant, because I in the embedded aspect and RTK is small white, so whether it is embedded communications or RTK have to learn from the beginning. The embedded aspect intends to use the stm32 to carry on the transplant, now already basically grasps the serial port communication method
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.