When we use Telnet to log on to the device, the user name and password are transmitted in clear text, in order to ensure the security of the data, we recommend the use of SSH login device. The following is the configuration of the Cisco router SSH:1. Configuring hostname and Domain-nameR1 (config) #hostname R1R1 (config) #ip domain-name frame.com2. Generate the key, here is the 1024-bit key, the key length
Router tplink845 cannot login the solution of the management interface:
The operating computer can connect the router through a network cable or wirelessly. It is recommended that you use a wireless connection to log in to the router management interface.
The computer cannot log in to the admi
Router tplink845 The workaround for logging on to another interface:
Broadband connection errors may enter the cat's interface, be sure to connect the broadband line (or through the cat's network cable) to the router Wan, as follows:
Computer to connect the LAN port of the router, if it is a wireless terminal, make sure to co
There are two ways to log in to a route. One is the console and the other is using Telnet, because my computer is Win7 and does not support the console. Also do not bother to install software, use Telnent as an example. A. Open Telnetclient For XP. Ability to perform telnet directly. But Win7, but first to open.watermark/2/text/ahr0cdovl2jsb2cuy3nkbi5uzxqvbghjmtewnq==/font/5a6l5l2t/fontsize/400/fill/i0jbqkfcma==/ Dissolve/70/gravity/center ">Then locate the turn Windows feature on or off:waterma
There may be two reasons for this situation:
One is the browser problem I change the browser or the following to clear the cache, the other is the password modified is not the original admin password we may restore factory settings.
Solution One
1. To solve the browser problem first we open it, then click "Tools" on the menu and click "Internet Options" in the dropdown below.
2. Furthermore, we click on "Internet Options"--click "General"--"Delete"--"Delete browsing History"-"OK" on it.
Enable password, enter the password for the setting starrrr#Rrr#exit[Connection to 192.168.1.1 closed by foreign host]! Use the exit command to exit Telnet loginrr#"Note items"If you do not configure the Enable password, you will not be able to log on to the switch for configuration and can enter user mode, butUnable to enter privileged mode, the second-level switch is now prompted with "% No password Set", three-layer switchingMachine at this time the prompt message is "Password required, but
Most of the operation of the router address is 192.168.0.1, generally as long as the input of this address can easily enter the router management interface, but sometimes it is not so will appear login password or user name error, especially in some installed ESET anti-virus software computer is so.
Today we will solve this problem, first click on th
performed in the factory status. You must enter admin in the user name and admin in the password (lowercase letters ). The interface style is as follows:If an error is prompted, the password may have been changed (that is, it is not in the factory status). Reset the vro (see the end of the article.[3]A few portable routers: No logon Username. The default password isAdmin.Such as TL-WR702N, TL-WR710N and other portable mini router, the default
tplink Routers modify logon username and password methods
01 First Use network cable to connect the router and computer, and then open the Computer Browser, in the URL bar input 192.168.1.1
02 Enter the setup field will let you enter the username and password.
03 go to the left of the menu bar to find the "System Tools" point open to find "Modify login password."
04 in the Modify in
There are two ways of landing routing, one is console, the other is to use Telnet, because my computer is Win7, not support console, also do not bother to install software, use Telnent as an example. One, turn on the Telnet client For XP, you can run Telnet directly, but the Win7 will be turned on first.Then locate the turn Windows feature on or off:Check the Telnet client on the OK....two, get router ip,then logi
I want to log on to my Linux today. So you can log on to your Linux when you are in the computer room class. Oh. Using VNC to achieve it. First, the successful login on the LAN is realized. But it makes sense to have an extranet login. Then because the dormitory is using the adsl+ router's Internet access mode. Then through static ip+ port mapping can realize the extranet
This article describes in detail how to set the vro remote Logon Settings from the aspects of default configuration, user name and password, and environment introduction. I believe this article will help you.
By default, the telnet function is enabled on the Huawei 3COM device. That is to say, we can connect to the control interface of the vro through the CONSOLE port of the Management CONSOLE without any configuration, but also use telnet for management, however, in order to allow us to manage
Telnet login authentication Mode has Aaa,password,none, here we use AAA and password two authentication mode for experiment, R2 authentication mode for PASSWORD,R3 authentication mode is AAA, finally through Telnet login verification effect.Step One: Configure each interface IP address, configure RIP protocol, so that each router can communicate with each otherR1
P-link Router Change Logon address setting method
We need to open the Internet Explorer browser in the Address bar input: 192.168.1.1 This IP address, this is only factory factory default address, we can change according to their preferences for their easy to remember the login address.
Click "Network Parameters" and "LAN Port Settings" in turn.
The LAN port settings interface appears on the
be:quidway_host
The range of public key size is (512 ~ 2048).
Notes:if the key modulus is greater than 512,
It would take a few minutes.
Input the bits in the Modulus[default = 512]:/The default digits of the master key are 512 bits/
Generating keys ...
..............++++++++++++
.++++++++++++
....................++++++++
.......++++++++
2, the use of SSH client software putty, input "Huawei/huawei" can successfully login system
Prompted
1, "experimental purpose"Learn how to enable telent on the switch, enabling remote access to the switch via Telnet.2. "background description"When the Enterprise Campus network coverage is large, the switch will be placed in different locations, if the switch is configured each timeNeed to be configured onsite at the location of the switch, the workload of the administrator will be large. This can be done on the switchTelnet configuration, so that when you need to configure the switch, the admin
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.