sample network design using packet tracer

ObjectiveLearning Network knowledge of the students have heard or used the network device Simulator, network equipment simulator known to have Huawei's ENSP, Third HCl and Cisco PACKET TRACER, Cisco's simulator with a simple operation interface, Easy to install and use and a

Packet Tracer Introductory One, Packet tracer introductionPacket Tracer is an assistive learning tool released by Cisco, which provides a network simulation environment for beginners in learning Cisco Web courses to

Packet Tracer Introductory One, hub overview The received signal is amplified by reproducing and shaping to enlarge the transmission distance of the network, and all nodes are concentrated on the node which is centered on it. Work at the bottom (physical layer) of the OSI (open System Interconnect Reference Model).II, Hub classification Pas

Linux Network Application Programming Packet Tracer installation and interface introduction, packettracerIntroduction to Packet Tracer 1 Packet tracer is an auxiliary learning tool rel

: Configure the wireless routerStep Two: give the client PC2 Add a wireless cardOn the PC, there is only one "Fast Ethernet" interface, and no wireless card.First click on the PC power switch, the PC shutdown, and then the lower PC Ethernet card to the point where the sword, the Ethernet card removed, and then drag the wireless card to the location of the Ethernet card just now, and then click on the PC power switch, the PC boot, the four-step is to the simulator of the ordinary PC to add wirele

I. Lab Objectives Understand the principles and functions of NAT network address translation; Master static Nat configurations to enable LAN access to the Internet; Ii. Lab background To publish the WWW Service, the company now requires that the Intranet web server IP address be mapped to a global IP address to allow external networks to access the company's internal web servers. Iii. Technical Principles

Tags: process proc ima RAC Technology share static term ADOBy configuring static routes, you can achieve an increase in routing entries for routers in a relatively simple network.However, if there are more than 20 routers in a network, it is difficult to configure static routes to accommodate the complexity of routing entries and changes in the network. At this point we can use the RIP protocol to configure

Linux Network Application Programming Hub (Packet Tracer simulation), packettracerIntroduction to Packet Tracer 1: Overview of hubs Connect to the received signal for regenerative shaping and amplification, to expand the transmission distance of the

port to enable ACL policyNetwork topology1, configure Router 1, turn on the single-arm routing configuration subinterface address and connect the physical interface address of another route and open the port2 Configuring the VLAN of the switch, configuring the port type3 Configuring the IP address of the PC, specifying the gateway4 Configuring router static routing to enable network interoperability5 Create a new ACL policy on the destination router6

policy in Router 2, specifying host and port7 The ACL takes effect under the port of the Router 2 Xia Lian serverNetwork topology1 Configuring Router 1 single-arm routing, establishing sub-interfaces and configuring IP addresses, etc.2 Configuring the Switch's VLAN and port type3 Configuring the IP address of the PC4 Configuring the interface address for Router 25 Configure static routes to communicate properly between networks6 Configure the ACL policy on Router 2 to allow PC1 to access the se

Packet Tracer 5.2 Experiment (15) network port address translation NAPT configurationFirst, the experimental target Understand the principle and function of NAT network address translation; Master NAPT configuration, realize LAN access to the Internet; Second, the experimental backgroundCorporate offi

, o-ODR p-periodic downloaded static routegateway of last resort is not sets 192.168.1.0/24 [1/0] via 200.1.1.1c 200.1.1.0/24 is directly connected, serial/0C 200.1.2.0/24 is directly connected, fastethernet0/0r2 # R2 # R2 # R2 # R2 # PC1: Packet tracer PC command line 1.0 Pc> ipconfigip address ......................: 192.168.1.2subnet mask .....................: 255.255.255.0default gateway ............

Nat[network address translation] In the absence of IP address in the case of a great use, it can not be normal Sisu network of the intranet address into a legitimate external network address on the public network to send and receive data. At the same time address translation function can also be very good to hide and p

Network address port Conversion NAPT is a very familiar way of transformation. NAPT is commonly used in access devices, which can hide small and medium-sized networks behind a legitimate IP address.Unlike dynamic address NAT, NAPT maps An internal connection to a separate IP address in the external network, adding a TCP port number selected by the NAT device to the address.This time, let's get to know napt.

Tags: cal enhancement packet share image share access Cisco virtual SRCVLAN, the virtual LAN (Virtul local area network), the VLAN divides the physical connected LAN logic into different virtual networks, its existence can reduce the broadcast domain, enhance the network security and convenient and flexible networking, adding PCs and switchesBy configuring VLANs,

Tags: size src zone sha port text topology Cisc-oTwo networks in different regions if you want to communicate, you need to configure routing on the router to implement the packets across the networkRouters can connect to multiple networks, but the router itself does not know about other networks, and we need to manually configure static routes to let routers know about other network information or to configure dynamic routing to let routers learn abou

RIP protocols can be configured in a more convenient way, but the limitations of RIP itself indicate that it is not suitable for medium to large networks. In contrast, OSPF is more complex to configure than RIP, but its functionality and performance are better than RIP.Configuration ideas1 Configure the physical interface address of the router Xia Lian switch and the physical interface address of the router to the other router and open the port2 Configure the address of the switch Xia Lian PC an

, adding switches and end devices1, double-click switch into switch command line (CLI) mode, switch configuration mode by command2 in most cases for security reasons, you need to configure the switch privileged mode passwordValidation test3 Configuring the telnet login switchTo achieve remote login, first need to configure the login user and device management addressVerify the configuration by matching the IP address of the PC with the switch management address into the same

Through the previous experiment we learned that by configuring VLANs, the terminals under different VLANs could not communicate with each other, but if you wanted to communicate between different VLANs, you would need to configure inter-VLAN routingLayer three switches have the capability of the network layer and can be forwarded via the routing functionNetwork environment1 set the IP address and gateway of the terminal (192.168.1.1 and 192.168.2.1, r

Tags: color-o switch test one-arm routing access via interface implementation representationTo achieve inter-VLAN communication, in addition to configuring the SVI interface on the switch, you can also implement VLAN data forwarding by configuring sub-interfaces under the physical interface of the router.Configuration ideas:1 The access switch configures the corresponding VLAN and sets the access PC port to access mode2 Setting the physical interface of the router to which the switch is connecte