Uninstall SD card:1. in the Android phone, I "set" rarr; "storage" rarr; "uninstall SD card" on the mobile phone ", in the displayed "uninstall SD card" window, click "OK" t
current folk self-made Rom basically requires that the SD card has three partitions to ensure that the Rom is successfully flushed and works properly.
The three partitions are:
(1) FAT32 primary partition: Common SD card space for file storage;(2) ext4 primary partition: used for app2sd. The Rom will automatically
1. Description of the phenomenon1) using the IMX6 Development Board, load 9 feet of 8G SanDisk SD card, the SD card read and write files are normal2) after inserting the 9-foot SD card
SD Card write protection How to remove the solution:
Step 1, about the SD card write protection How to remove the problem, you can use the disk repair program to repair the SD card. Op
BL1 code.
3) BL1 can initialize the system clock, UART, SDRAM, and other devices, and then copy bootloader2 (bl2) to the address memory of the SDRAM.
4) then jump to the "bl2" in the SDRAM to continue running. bl2 supports more powerful functions, and further initializes the hardware and copies the wince kernel image to the memory of the (0x80100000) Address of the SDRAM.
5) execute NK again in the SDRAM mode.
Figure 2 startup modes supported by cloud6410
Here is an uncertain
The SD card has been watched for two days. It is mainly because the tested card capacity is incorrect, so I have been searching for the reason and finally found out that the total ratio is just a problem with the unit, maybe it's because I haven't touched SD before, so I don
Causes of SD card data loss
Why are SD card files lost? Is the opening method incorrect? Or cannot the SD card be read by the computer? In fact, there are various factors that may cause SD
after inserting the SD card, the computer prompts the format reason analysis : When the use of multiple reader access to the computer, the SD card will appear on the letter, double-click on the "whether to format" prompts, there may be a problem with the
to the SD card image file and add support options for the SD card
Open Eclipse, enter: Window->android SDK and AVD manager such as:
At the time of creation, in the SD card column, select File and set it as the p
My phone SD card needs to be divided into two partitions, under the WINDOWXP.The main problem is that window only knows the first partition of the SD card.Someone modified the driver to let Windows recognize the SD card as Hitachi
The cell phone SD card is an important tool for storing application and data, but how to solve the problem? When the SD card prompts to format, but the things that carry is important how to do? Maybe you could try the following SD
bytesDisk identifier:0x00000000Device Boot Start End Blocks Id System/DEV/SDC1 2048 6293503 3145728 b W95 FAT32//windows/DEV/SDC2 6293504 15523839 4615168, Linux//linuxCommand (M for help): w//OK, save itThe partition table has been altered!Calling IOCTL () to re-read partition table.Warning:if you has created or modified any DOS 6.xpartitions, please see the Fdisk manual page for additionalInformation.OK, basically 、、、、 Emma, no, not yet formatted yet.Go on:sudo mkdosfs/dev/sdc1//formatted FAT
Believe that a lot of friends have encountered such a problem, that is, through the card reader will be inserted into the computer SD card Computer "whether to format" prompts, and the SD card inserted into the camera, and the "
In the mobile phone use of the process began to often have friends with the mobile phone SD card can not be formatted to read the problem, for the SD card can not be formatted to produce a lot of reasons, but many cases are some small problems, the following teach you how to
attributes based on these response.Card read/write: The file system read/write will first go to the sdmemory layer. sdmemory first converts cardio to diskio and then passes it to the host controller through the bus layer. The read/write mainly consists of memory 17 and memory 18, and listen 24 and listen 25. After each processing of the bus layer, you must send a busrequest handle complete event to the bus layer to notify the bus layer that the read and write operations have been completed. The
of the comments, modified as follows:__return: rt_kprintf ("SDcard init failed\n"); Gpio_setbits (gpioc,gpio_pin_7); /* SD card Power down */ return 0;} Init_device_export (Rt_hw_sdcard_init);Save after the modification is complete.(4) Open the Application.c file, locate it near line 114, and add the following code:/* Mount SD
1. Problem description: purchase ZTE v955 as a mobile phone, but in order to save costs (the virtual SD card space of the mobile phone system is 1.7 GB, meeting actual requirements), it is not necessary to buy an external memory card. Write a program to save images and a large amount of data on the
SD card mounting file system: VFS: Cannotopenrootdevice quot; mmcblk0p2 quot; solve the problem of using the initramfs file system. linux can run normally and read and write SD cards normally. However, if it is mounted to the SD card
Assume that you use the default system administration, which is placed by default under packages. More worry. and will not cause data residue after uninstalling the app. But there is also a problem. For example, I do a back word software, then when the user uninstalled the app, he worked hard to download the word library also lost ...So I think of the solution. is to change the database path. Do not put it below the package and put it on the
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.