sata 15k hard drives

SATA interface. 8. Q: it is said that SATA hard drive supports hot swapping. Can this function be used?A: currently, the SATA technology is divided into V1.0 and V2.0 versions. V1.0 does not support hot swapping, and SATA implements hot swapping in V2.0.Only the motherboard

, so its biggest advantage is that its system occupancy rate is very low, but the speed, high transmission rate of SCSI interface hard disk also has its shortcomings: high prices, installation inconvenience, but also need to set up and install the driver, so this interface hard disk is mostly used for high-end applications such as servers. It is the use of a 50-core flat cable, RPM above, but with the devel

SAS hard Drive, is a serial connection to the next generation of SCSI technology, the use of serial technology to achieve higher transmission speed, and by shortening the connection line to improve the internal space. SAS is a parallel SCSI interface that develops a new interface. Improves storage system performance, availability, and scalability, and provides compatibility with SATA

devices. At this point, the SATA1 disk corresponds to third IDE master (the third IDE Channel Master disk), and the SATA2 port hard disk corresponds to fourth IDE master (Fourth IDE channel Master disk). S-ata: Serial hard drive enhanced mode, which theoretically supports 4 serial hard drives, but also depends on the

the entire image process, only half of the disk capacity is valid (the other half is used to store the same data ). Compared with raid 0, raid 1 First considers security, halving the capacity, and changing the speed.Raid 0 1To achieve high speed and security, raid 10 (or raid 0 1) can be simply split into a raid 0 array consisting of multiple disks for mirroring.Raid 3 and raid 5Both raid 3 and raid 5 are verified. Raid 3 uses a disk to store verification data. The corresponding data verificati

Motherboard SATA connector does not recognize the hard drive reasons and solutions: One, the hard disk can not use the fault 1, BIOS setup Error Mainly in the BIOS on the SATA Setup error, especially some early motherboards using a Third-party sata/raid control chip, but

SATA The full name of Sata is serial Advanced Technology Attachment,Proposed by Intel, IBM, Dell, APT, maxtor, and SeagateHard Disk InterfaceSpecification. The SATA hard drive adopts a new design structure, which features fast data transmission and space saving. It has many advantages over the IDE

The server configuration is as follows:XEON5506 (2. 13)Memory: KST 4GB DDR3 ECCHard drive: st300g SAS-15000 to *1+1t Western Data enterprise-class hard driveMotherboard: Asus Z8ANA-D6+6480*1Chassis: 1U rack TypePower supply: 1U 400WAfter the assembly is ready, installation of the system found in the Win2003 installation interface hard disk partitions are normal, but to select the SAS

Hard Disks include SSD, HDD, and HHD. SSD uses flash memory particles for storage, HDD uses magnetic discs for storage, and hybrid hard disks (HHD: hybrid hard disk) is a hard disk that integrates the magnetic hard disk and flash memory. HDD:

blueprint, so the use of four-core wiring; the demand voltage is significantly reduced to 250mV (highest 500mV), compared to the traditional parallel ATA interface 5V 20 times times less! Therefore, manufacturers can give serial ATA hard drives are attached with advanced hard drive features, such as hot-swappable swapping. More importantly, in the form of connec

multi-language support package, with a total of 3 CDs. The simplified Chinese, traditional Chinese, and Korean language packs are in 3rd CDs, which can also beHttp://download.microsoft.com/download/fdafdac56ee-928a-Download 4d51-9d6d-c7c64e9f5baARMMUIx3.iso.　　Install 64-bit XP on SATA hard drive1. You must use a CD-ROM for boot installation.First, the Tester Used winrarto release ws03sp1_rtm_1830_px6_en.is

When using the SATA interface hard disk to install XP system, there is a panic, blue screen situation, show "Unknown Hard errorsystemrootsystem32ntdll.ll" error. Since the SATA interface appears later than the XP system, the SATA driver needs to be invoked when the s

After entering the DOS, the operation of the Ghost machine will stop not moving, into a false panic phenomenon. If you enter the PE run ghost will be blue screen. The main reason for this is that the ghost version is too low (version less than 11) and does not recognize Sata's optical drives and hard drives. When the ghost starts, it detects whether the IDE

What's the difference between SSD and msata? What is the difference between a solid-state hard drive sata and a msata, I want to add a solid-state drive to my notebook, but when I choose a solid-state drive, I see a SATA-interface SSD and a mSATA SSD, and I don't know how to choose 1.8-inch SATA, that is, Microsata (

Many friends have acquired a notebook and encountered some difficult problems. Usually install XP when the blue screen or install half of the time the copy file failed! This is generally the problem of hard disk, here is not to say hard disk physics problems, software problems. Serial ATA hard disk, Serial ATA bus with embedded clock signal, with a stronger abil

Friends who often use hard drives should be very familiar with SATA drives. In fact, in our Win7 system can be very good use of SATA port this function, it can not only speed up the speed of our hard disk transmission, but also to

window and restart your computer. 4. when the system starts, press "F2" (depending on the computer's key) to go To the BIOS settings page and change the hard disk to "AHCI" mode. The general position is: "Devices" → "ATA Drives Setup" → "Configure SATA as" → "AHCI", save and exit BIOS. 5. After the system is restarted, it is successfully modified to the AHCI int